Kenmore ULTRASOFT 250 625.38826 - Manual (Page 10)

JJUJJ J J J.JJ J
J.JJ JJ
SECTION
2 illElS] HOW YOUR WATER SOFTENER WORKS
A. FACEPLATE TIMER FEATURES
s
E
C
T
I
o
N
ijjjjjjjjjjjjjjjjj
UJJJJJJJJJJ-JJJJ JJ
IJJJJUJJJJJJJJJJJJ
IJJJJP^JJJJJJJJJJ
IJJJJ J Jjjjjj JJJJJ
IJJJJ^OJJJJJJJJ JJ.
IJJJJK
j JJ JJJJJ JJ JJ
ijjjjjjjjjj
IJJJ9999 jj JJJJJJJJ
ijjjjjjjjjjJJjjjjJ
jjjjjjjjjjjjjjjJJ
ijjjjjJJjjjjjjJJJJ
^ EXTRA RECHARGE
Sometimes, a manually started
regeneration (recharge) may be
desired, or needed. Two exam­
ples are:
- You have used more water than
usual (guests visiting) and you
may run out of soft water before
the next timer started regenera­
tion.
- You did not refill the softener
with salt before it was gone. After
you refill with salt:
You can start a regeneration right
away, or you can set the timer to
regenerate at the next 2:00 AM (or
other preset recharge time). Do
the following.
^ RECHARGE NOW "i.nn,
I'UU
PECHAPCE
Press the ON/OFF-HOLD but­
ton and hold until ^RECHARGE,
Serv and Fill begin to flash in the display. Upon
reaching fill, the first cycle of regeneration, the flash­
ing Serv goes off and Fill is on steady. RECHARGE
continues to flash. This regeneration will last for
about 2 hours. After the 2 hours, you will have soft
water again.
*Note:
If the CLEAN feature is set to ON, a cleaning back­
wash {CLEAN and Bkwsh or Rinse flashes in the dis­
play, along with the minutes of the clean cycle re­
maining) precedes the recharge.
« OFI
7
• IDS-
RECHARGE TON/GHI
7
*vAT£ft F l o w
^ RECHARGE TONIGHT
Press and release (do not hold) the
ON / OFF-HOLD button. RE-__________
CHARGE TONIGHT flashes in the display, and the
softener begins regeneration at the next preset re­
charge time. Press and release the ON/OFF-HOLD
button once more if you decide to cancel the regen­
eration, and RECHARGE TONIGHT.
y
SALT MONITOR SYSTEM
The face plate timer has a low salt monitor with an
indicator light to remind you to refill the storage
tank with salt. To set this monitor system:
Lift the salt hole cover and level the salt in the
storage tank.
The salt level decal, on the brinewell inside the
tank, has numbers from 0 to 8 (see drawing be­
low). Observe the number the leveled salt is at
or closest to.
Now, press the SALT LEVEL ADJUST button
until black bars display up to the salt level num­
ber. For example, the pictures below show the
salt level at 6.
Finally, set the level you want the low salt indi­
cator light to come on. Press the SIGNAL LIGHT
ADJUST button until a (^) shows opposite this
number. In the example below, the light will
come on when the stored salt drops to level 2. At
level 2, the storage tank is about 1/3 full. This is
the lowest you should allow the stored salt level
to drop to (see note on page 1-6).
If you wish to turn the salt monitor off, press the
SIGNAL LIGHT ADJUST button until OFF
shows above.
Note:
Your salt monitor is an estimate of your salt lev el; ac­
curacy depends on the type of salt used and other
regeneration characteristics.
2
-
1
Problems, Questions? Call 1-800-426-9345 Kenmore Water Line