Brother PT-80 - Manual

brother.
OCD o o o
a o o o o
o' o" o“
oooooooooo
ooooooooo
00 (
iuciMW*“«“***’'*”"
PT-80
USER'S GUIDE
English / Español
Printed in China
LN8233001®
www.brother.com
INTRODUCTION
With your PT-80, you can create labels for any application. Select from the
many frames, character sizes and styles to design beautiful custom labels. In
addition, the variety of tape cartridges available allows you to print labels with
different widths and exciting colors.
Read this manual carefully before starting and keep the manual in a handy
place for future reference.
FCC NOTICE
This device compiles with Part 15 of the FCC Rules. Operation is subject to the following fwo conditions: (1)
This device may not cause harmful Interference, and (2) this device must accept any interference received,
Including Interference that may cause undesIred operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
Interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the Instructions, may cause harmful Interference to
radio communications. However, there is no guarantee that Interference will not occur In a particular
Installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment Into an outlet on a circuit different from that to which the receiver Is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user’s
authority to operate the equipment.
GENERAL PRECAUTIONS
Use only Brother M tapes with this machine. Do not use tapes that do not have
the ^ mark.
Do not clean the machine with alcohol or other organic solvents. Only use a soft, dry
cloth.
Do not touch the print head mechanism. Use a soft wipe (e.g. a cotton swab) when
cleaning the print head.
To avoid injuries, do not touch the cutter's edge.
To prevent damage or breakage of the LCD glass, do not press on the display.
Do not put any foreign objects into or heavy objects on the machine.
Do not leave any rubber or vinyl on the machine for an extended period of time,
otherwise the machine may be stained.
Do not get the machine wet, such as by handling the machine with wet hands or
spilling beverages on to the machine.
Do not expose the machine to extremely high temperatures or high humidity. Never
leave It on the dashboard, In the back of your car, near heaters or other hot
appliances. Keep It out of both direct sunlight and rain.
Avoid using the machine In extremely dusty places.
Depending on the environmental conditions and the applied settings, some
characters or symbols may be difficult to read.
Do not pull on the tape being fed from the P-touch iabeier, otherwise the tape
cassette or P-touch Iabeier may be damaged.
Do not attempt to cut the tape while printing or feeding since this will damage the tape.
Do not try to print labels using an empty tape cassette set in the P-touch labeler. Doing
so will damage the print head.
Remove the batteries if you do not intend to use the machine for an extended period
of time. (Note: When power Is disconnected for more than two minutes, all text and
format settings will be cleared. Language, unit and clock settings will also be cleared.)
Make sure that the power Is turned off when replacing batteries or tape cassette.
Do not use old and new batteries together or mix alkaline batteries with other type
batteries, or set the positive and negative end in the wrong position. Otherwise, the
batteries may leak or be damaged.
PREPARATION
Unpacking Your P-touch Labeier
Check that the package contains the followings before using your P-touch
labeler.
PT-80 M tape cassette
Included items may differ by distribution.
Power Supply & Tape Cassettes
Remove the back cover by pressing in
the rough area at the top end of the
machine.
If a tape cassette Is already Installed,
remove It by pulling It straight up. Also, If
batteries are already Installed, remove
them.
• Make sure that the power Is turned off
when replacing batteries or tape
cassette.
Print head
Insert four new AAA-size alkaline
batteries (LR03), making sure that
their poles point in the correct
directions. Always replace all four
batteries at the same time using brand
new ones.
Insert a tape cassette, making sure that it snaps into place.
Tape guide
Cutter's edge
End of tape
Tape exit slot
• Make sure that the end of the tape feeds under the tape guides.
• Use only Brother M tapes with this machine.
Attach the back cover by inserting two
hooks at the bottom into the slots on
the machine, then pushing down
firmly on the cover until it snaps into
place.
• After you have installed the tape, feed
the tape ( -I- ) once and
then push In the tape cutter lever to cut
the tape.
Tape cutter lever
£
OPERATION
Keyboard & LCD
Size---------------- Width I ' I I I
A
A
A/A f i ñ A
--------------- Style
Cursor--------------
1
i-! / / !
Num Lock
Print key
Preview key
Power key
Character keys
Shift key -
Caps key -
Num Lock key -
Symbol key -
Caps-
Caps Num
___I I
ABC/IÂBCl ■ Underllne/Frame
— Label Length
\ 'ia) (S) ©' ©* ©' ©' ©' ©' I ! if Backspace key
-r. © © © © © © © © © ©/ /
TIme/Date key
Function ke
Cursor key
/ \v Function key
, ® © © © © © © ® © ©/
^.V.©.®.©.®.® ®.® 0.0/
brotler
H^/y
~
■ Shift key
Enter key
- Accent key
Space key
The LCD shows one row of 12 characters; however, the text that
you enter can be up to 80 characters in length, which will scroll
across the display.
Use Cursor key while holding down Shift key to go to beginning /
end of the text.
Initial Setting
Start your machine
Supply power by using four AAA batteries, and then press (@
Set the language (English/Spanish/French/Portuguese)
* English *
Choose a language with II ^J) and press
Set the unit (inch/mm)
inch
T Choose a unit with C"* II *•]) and press ( —' ) .
Set Date (MM/DD/YY) and Time (hh:mm)
Example: setting the clock to March 20th 2006, 10:30AM
Date (MM/DD/YY)
input “03”
Time (hh:mm)
I hh:00 I
input “10”
input “20”
input “30”
input “06”
Select AM/PM with II and press ( ).
You can also confirm the figure and move to the next setting by using
right cursor key.
• The machine automatically turns off if no key is pressed within 5
minutes.
• To cancel operations, press @).
• To initialize the P-touch labeler back to factory settings, turn off the
machine and then while holding down //wf// and press to
turn the machine back on. Finally, release / and
[GETTING STARTED]
Troubleshooting
REFERENCE
Error message
Message Cause/Remedy
Battery The batteries are weak.
Replace them with new ones.
Invalid Invalid number is selected for Label Length setting.
No Text • The Print key or Preview key is pressed when no text is
entered.
• You tried to set Copies (copy printing) when no text is
entered.
Line Lmt Line Limit. Printable lines are limited up to 2 lines.
You tried to enter a 3rd line by pressing Enter key.
Full The maximum number of characters (80 characters) have
already been entered.
Text Lmt Text Limit. The text length exceeds the selected label length
or the selected Auto Format setting length.
What to do when...
Problem Solution
The display stays blank
after you have turned on
the machine. • Check that the batteries are correctly inserted.
• If the batteries are weak, replace them.
Language setting of the
machine is incorrect. • Turn off the machine and then while holding
down ©*7 and ©), press to turn the machine
back on. Finally, release ©© and ©).
• Note: The text and formats in the display are erased. Also,
the language, unit and clock settings will be cleared.
The machine does not
print, or the printed
characters are not
formed properly. • Check that the tape cassette has been inserted correctly.
• If the tape cassette is empty, replace it.
• Check the cassette cover is properly closed.
The setting has cleared
on its own. • The batteries may be weak. Replace them.
• When power is disconnected for more than two minutes,
all text & formats in the display will be lost. Language, unit
and clock settings will also be cleared.
A blank horizontal line
appears through the
printed label. • There may be some dust on the print head. Remove the
tape cassette and use a dry cotton swab to gently wipe the
print head with an up-and-down motion.
The machine has
"locked up" (i.e., nothing
happens when a key is
pressed, even though
the machine is on). • Turn off the machine, and then while holding
down /©// and ©), press to turn the machine
back on. Finally, release ©© and ©).
• Note: The text and formats in the display are erased. Also,
the language, unit and clock settings will be cleared.
The power turns off
when you try to print. • The batteries may be weak. Replace them.
The tape does not feed
properly or the tape gets
stuck inside the machine. • Check that the end of the tape feeds under the tape
guides.
• The cutter lever is used while printing. Do not touch the
cutter lever during printing.
All text and format
settings need to be
cleared to create a new
label. • Press Backspace key while holding down Shift key, or go
9
into Function mode and select (©
Specifications
Item Specification
Dimensions 6.8" (W) X 4.0" (D) X 2.3" (H)
(172 mm (W) x 100 mm (D) x 58 mm (H))
Weight 0.5 lbs. (240 g) (without batteries and tape cassette)
Power supply Four AAA-size alkaline batteries (LR03)
Tape cassette Brother M tape (width):
0.35" (9 mm), 0.47" (12 mm)
See the attached “Supplies and Accessories Guide” for detailed info of tape
variation.
ki
MAKING TEXT DESIGNING LABELS
Switching Upper Case/Lower Case
©■►® ® © ®
Upper case ( O N ) Lower case ( O F F )
R E C D a b e d
Caps
Entering Numbers
© ♦ (Ô) (w) ©’
Num Lock ON Num Lock OFF
1 2 3
Num
Entering Symbols
Symbol) ^ (© ►]) . ^ . II 1 .
Group Symbols
1 " ' •
■ 5 ■ 5
2 @ - &
~ \
/
3 # % ? !
¿ i *
4 -F - X -F ± =
5 ( ) [ ] < >
6 t \
Group Symbols
7 $ (t € £ ¥ ° /
8 " ^ • O A V J»
9 O A ^ ^ 13 tì
10 $ @ ^ ft ^ é ^
11 W U ' i t ^ ^
To go to the next group, press (5^.
To cancel operations, press
Entering Accented Characters
(T) ^ (T) II >■]) ^ )
Accented Characters
A В А В А Ж В A A а А
c
Ç C C
D D D
E Й И К Л ^ Л Й Й
G Q G
1 [ О О I [ T i
K K
L L L l \ L
N N N N N
0 Ф Ф Ф 0 Ф Ф Œ Ô
R R R R
S и й § § f t
T T T R
u ы щ ы ь g ù o û
Y Ÿ Ÿ
Z z z z
Accented Characters
a
а а в в ж в ^ в в в
c
Ç C C
d
d ’ ô d
e й и к л з л й л
g g g
i
i М о п i T 1
k
1 l Î U ’
n
n n h з
0
ф ф ф 0 ф ф œ ô
r
r r i
s
s s
§
§ ft
t t î D
u
Щ Щ ( J Ü L [ Щ Ь Ы
y я я
z
z z z
To cancel operations, press (^.
The order of accented characters differ by the selected LCD language.
Making Two Line Text
Move the cursor to where the second line starts and press i
Display Label image
OLbe^Jde-f abc
def
Setting [Size]
( @ + ® )
Text Preview
PRINTING LABELS
^ (00 [Size] ( ^ (0B [Large] ( ^ )
[Large] [Small]
J.SMITH
Setting [Width]
(© + (w))
[Normal]
[Width] ( —' ) '
[X2]
№)[ x 2100
[X1/2]
J.SMITH J . S I V I I T H
Setting [Styie] (Vertical) ( © + © )
[Normal]
[Style]
[Bold]
[Vertical] (0©
[Outline]
J.SMITH J.SMITH D©
[Shadow] [Italic] [l+Bold] (Italic Bold)
J . S M I T H J . S M I T H
[l+Outl](ltalic Outline) [l+Shadow](ltalic Shadow) [Vertical]
TN J. I T N CO ^ — I- X
Setting [Undl/Frm] (Underline/Frame) (© + ©')
©■ [Undl/Frm] C0© ■
[Off] [Undl] (Underline) [Round]
ABC ABC fAB^
[Callout] [Banner] [Wooden]
^T a BC] VABCl,^ ^ABC:i
Setting [Length]
(Labei Length)(AutD/i.2"-i2.o")
[Undl] ( —' )
[Candy]
(© + ©)
.4 IF'') [Length] C0Z) '
• You can also select the length by entering the length with ® ®.
• To return to [Auto], press ( space ) .
Setting [A/F](Auto Format) (®+®‘)
You can choose label length from five formats to create labels for various
applications.
©-►0[9)[ a / f ]GD->-Q[9)[ vcrvhs ]GD
LCD Application Length
VCR VHS Cassette spine 5.5"
MiniDV Cassette spine 1.6"
Audio Cassette case spine 3.5"
File Tab File tab 3.2"
Divider Divider Tab 1.6"
To Clear
By pressing the backspace key you will delete a character.
(To delete a whole line of text, keep pressing the Backspace key)
To Clear All the Text and the Settings (®+®’)
@
Shift / + IfBSlj
This will not affect Time & Date or language settings.
You can preview the text before printing.
The LCD shows the whole text and the label length (inch/mm), then returns to the
original text.
Only the text can be previewed, not the font, style, size, underline/frame or any
additional features.
pGGding (Tape Feed)
Shift J +
The machine will feed 1.0” of tape, which may be needed when Installing a new tape
cassette.
Printing
• To cut off the label, push in the tape cutter lever on the upper-left corner of the
machine.
• To prevent damage to the tape, do not try to cut while the message "Print" or
"Feed" is displayed.
Using Copies ( ® + ® )
You can print up to 9 copies of each label.
© -► 00 [Copies] C0© "►
You can also select the number of copies by entering with ® ~ ®.
COMPLETED LABELS
OO2|-Cr<Ol-C0 CM o o m
_______________ y
S05(8632)-4112
ü[fa®ппоо
V(s)irfe <S)DO NOT TOUCH
< < < < K e n S a m p s o n > > > >
^ K e n . S @ P - t o u c h . c o m
M Merry X'mas é
Peel the printed label from backing and apply the label.
Removing the Label Backing
This machine is equipped with a peeler that allows you to easily remove the
backing from labels.
El Insert the label, with the printed surface facing down, as far as possible
^ into the built-in peeler.
e
T
Fold back the label to the right and quickly pull out the label. The end of
the backing is separated from the label.
[CREATING LABELS]
USEFUL FUNCTIONS
Time & Date Function ( ® + ® )
You can insert the desired time and date to your text at the touch of a button.
8 Formats are available for printing time and date.
You can change the number of time/date by changing the clock setting.
To add Time & Date to your text:
Thne/Datej / bc 03-^20-^06_
The cursor should be positioned where you wish to insert the time & date.
To select the format of Time & Date:
+ M/D/V hm *
Format Description Example
(March 20th 2006, 3:30PM)
M/D/Y Month/ Date/ Year 03/20/06
M/D/Y hm Month/ Date/ Year time 03/20/06 03:30PM
D/M/Y Date/ Month/ Year 20/03/06
D/M/Y hm Date/ Month/ Year time 20/03/06 03:30PM
D.M.Y Date. Month. Year 20.03.06
D.M.Y hm Date.Month.Year time 20.03.06 03:30PM
Y-M-D Year- Month- Date 06-03-20
Y-M-D hm Year- Month- Date time 06-03-20 03:30PM
To change the Clock Setting:
Example: setting the clock to March 20th 2006, 10:30AM
Setting Month (MM), Date (DD), Year (YY)
input “03” input “20”
Setting Hour (hh) and Minute (mm)
input “10” input “30”
input “06”
Select AM/PM with || *■)) and press ■
You can also confirm the figure and move to the next setting by using right cursor key.
Function Shortcuts (®+@)~®’)
In addition to the basic steps to search for a function, PT-80 provides you with
function shortcuts so you can easily jump to a frequently used function just by
pressing © and the shortcut key shown in the table below.
To confirm, press
( -> ) ■
Key Function
(§)
Size
Width
Style
©^
Underline/Frame
©^
Label Length
Key Function
©^
Auto Format
©^
Copies
©^
Time & Date
All Clear
Should you encounter any problems with your product, please do not
return your product to the store!
After referring to the User's guide, if you still need assistance, call Brother
Customer Service at:
Voice : 1-877-BROTHER(1-877-276-8437)
Web : www.brother.com
Fax : 1-901-379-1210
If you need to locate a service center, please call
1-877-BROTHER(1-877-276-8437) or visit
US at www.brother.com