Kenwood UD-952 - Manual (Page 81)

Specifications
(For U.S.A. and Canada}
FM Tuner section
Tuning frequency range...........................87.5 MHz *-108 MHz
Sensitivity (IHF)................................. 13.2 dBf (1.2 at 75 Q)
Signal to noise ratio at 1 kHz
MONO.......................................... ........75 dB (65 dBf input)
STEREO...............................................68 dB (65 dBf input)
Selectivity (IHF ± 400 kHz).................................................. 50 dB
Stereo separation (IHF at 1 kHz)........................................ 40 dB
Frequency response..............30 Hz - 15 kHz + 0.5 dB, - 3 dB
AM Tuner section
Tuning frequency range........................... 530 kHz ~ 1,700 kHz
Usable sensitivity......................................12 jiV / (500 |iV / m)
Signal to noise ratio............................................................ 48 dB
Pre Amplifier section
Total harmonic distortion
................... 0.006 % (SOURCE DIRECT, 1 kHz, 200 mV)
Input sensitivity / Impedance
MD / DAT, VIDEO, AV AUX......................... 200 mV / 47 kQ
MIC..................................................................... 1.3 mV/47 kfl
N.B. circuit...............................................................+ 8 dB (max.)
(60 Hz)
Output level / Impedance
MD / DAT, VIDEO...................... ................ 200 mV / 2.2 k Q
VIDEO section
Input level / Impedance
VIDEO (composite)......................................... 1 Vp-p / 75 Q
Input (VIDEO, AV AUX)
Output level / Impedance
VIDEO (composite).......................................... 1 Vp-p / 75
Output (MONITOR OUT,VIDEO)
[General]
Dimensions....................................... W: 270 mm (10-5 / 8")
H : 104 mm (4-1 /8")
D : 328 mm (12-15/16")
Weight (net)............................................................ 2.5 kg (5.5 lb)
Power Amplifier/Graohic eoualizer unit{B-E9)
Power amplifier section
Rated power output
STEREO MODE
65 watts per channel minimum RMS, both channels
driven, at 6 0 from 40 Hz to 15 kHz with no more than
0.08
% total harmonic distortion.
SURROUND MODE
FRONT.......................................70 W + 70 W (1 kHz, 6 O)
CENTER...................................................10W(1 kHz,8Q)
REAR...............................................Total 6 W (1 kHz, 8 Q)
Total harmonic distortion
............................0.02 % (1 kHz, 1 / 2 Rated power, 6 O)
Frequency response
Signal to noise ratio
Input sensitivity / Impedance
20 Hz ~ 70 kHz, + 0 dB, - 1.0 dB
............................105 dB (IHF'66)
...............1.0 V/47 kn
Output level / Impedance
SUPER WOOFER PRE OUT............... ........... 2.0 V / 600 Q
OMNI PRE OUT................................................2.2 V / 600 Q
Graphic equalizer section
Individual channel................................. 63 Hz, 160 Hz, 400 Hz,
1 kHz, 2.5 kHz, 6.3 kHz, 16 kHz
Equalizer characteristic variable range
....................................................................................±10dB
[General]
Power consumption............................................................. 2.2 A
Dimensions............................................ W: 270 mm (10-5 / 8")
H : 124 mm (4-7 / 8")
D :320 mm (12-5/8")
Weight (net)..........................................................6.5 kg (14.3 lb)
I Note I KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without
notice.
For the U.S.A.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause
harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- - Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
- - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- - Consult the dealer or an experienced radio / TV technician for help.