ebm-papst D3G146-LV13-01 - Manual (Page 5)

Operating instructions D3G146-LV13-01
Translation of the original operating instructions
3.2 Nominal data
Motor M3G055-DF
Phase 1~
Nominal voltage / VAC 230
Frequency / Hz 50/60
Type of data definition ml
Speed / min -1 1550
Power input / W 167
Current draw / A 1.3
Min. back pressure / Pa 0
Min. ambient temperature
/ °C -25
Max. ambient
temperature
/ °C 50
ml = Max. load · me = Max. efficiency · fa = Running at free air
cs = Customer specs · cu = Customer unit
Subject to alterations
3.3 Data according to ErP directive
Installation category A
Efficiency category Static
Variable speed drive Yes
Specific ratio * 1.00
* Specific ratio = 1 + p fs / 100 000 Pa
Actual Request
2013 Request
2015
Overall efficiency η es / % 37.8 25.6 32.6
Efficiency grade N 49.2 37 44
Power input P ed / kW 0.16
Air flow q v / m³/h 600
Pressure increase total p sf / Pa 334
Speed n / min -1 2455
Data definition with optimum efficiency.
The ErP data is determined using a motor-impeller combination in a standardised
measurement configuration.
3.4 Technical features
Mass 2.9 kg
Size 146 mm
Surface of rotor Galvanised
Material of electronics
housing PP plastic
Material of impeller Sheet steel, galvanised
Housing material PP plastic
Motor suspension Motor anti-vibration mounted on both sides
Direction of rotation Counter-clockwise, seen on rotor
Type of protection Motor IP 54, electronic IP 20
Insulation class "F"
Mounting position Any
Condensate discharge
holes None, open rotor
Operation mode S1
Motor bearing Ball bearing
Technical features - Output 10 VDC, max. 1.1 mA
- Tach output
- Motor current limit
- Soft start
- Control input 0-10 VDC / PWM
- Control interface with SELV potential
safely disconnected from the mains
- Over-temperature protected motor
Touch current acc.
IEC 60990 (measuring
network Fig. 4, TN
system) <= 3.5 mA
Electrical leads With plug
Motor protection Thermal overload protector (TOP) wired
internally
Cable exit Variable
Protection class I (if protective earth is connected by
customer)
Product conforming
to standard EN 60335-1; CE
Approval CCC
For cyclic speed loads, note that the rotating parts of the device
are designed for maximum one million load cycles. If you have
specific questions, contact ebm-papst for support.
3.5 Mounting data
For depth of screw, see chapter 3.1 Product drawing
; Secure the mounting screws against accidentally coming loose (e.g.
by using self-locking screws).
Strength class for
mounting screws 8.8
You can obtain additional mounting data from the product drawing if
necessary.
3.6 Transport and storage conditions
; Use the device in accordance with its protection type.
Max. permissible
ambient motor temp.
(transp./ storage) + 80 °C
Min. permissible
ambient motor temp.
(transp./storage) - 40 °C
3.7 Electromagnetic compatibility
EMC interference
immunity Acc. to EN 61000-6-2 (industrial
environment)
EMC interference
emission Acc. to EN 61000-6-4 (industrial
environment)
Item no. 51144-5-9970 · ENG · Revision 83605 · Release 2014-11-12 · Page 5 / 10
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com