Great Planes Easy Sport 40 ARF - GPMA1035 - Manual (Page 3)

Please inspect all parts carefully before starting to build!
If any parts are missing, broken or defective, or if you
have any questions about building or flying this
airplane, please call us at (217) 398-8970. If you are
calling for replacement parts, please reference the part
numbers and the kit identification number (stamped on
the end of the carton) and have them ready when calling.
1. Build the model according to the instructions. Do not
alter or modify the model, as doing so may result in an
unsafe or unflyable model. In a few cases the instructions
may differ slightly from the photos. In those instances the
written instructions should be considered correct.
2. Take time to build straight, true and strong.
3. Use a radio control system that is in first-class condition
and correctly-sized engine and components throughout
your building process.
4. You must properly install all components so that the
model operates properly on the ground and in the air.
5. You must check the operation of the model before every
flight to ensure that all equipment is operating, and that the
model has remained structurally sound. Be sure to check
nylon clevises or other connectors often and replace them if
they show signs of wear or fatigue.
6. If you are not already an experienced R/C pilot, you
should fly the model only with the help of a competent, well
experienced R/C pilot.
Remember: Take your time and follow directions to end
up with a well-built model that is straight and true.
Items in parentheses (OSMG2691) are suggested part
numbers recognized by distributors and hobby shops and
are listed for your ordering convenience. GPM is the Great
Planes brand, TOP is the Top Flite
® brand, and HCA is the
Hobbico ® brand.
❏
4 Channel Radio with 4 Servos
❏
Engine - See Engine Selection above
❏
Propellers (see engine instructions for sizes)
❏
18" Silicone fuel tubing (Great Planes #GPMQ4131)
❏
1/4" Latex foam rubber for receiver & battery
(Hobbico #HCAQ1000)
Note: Larger wheels than those included may be required
for operation on rough grass fields.
These are the building tools, glue, etc. that we recommend
and mention in the manual. We recommended Great
Planes Pro
™ CA and Epoxy
❏
1 oz. CA thin (Great Planes #GPMR6002)
❏
1 oz. CA+ Medium (Great Planes #GPMR6008)
❏
6-Minute Epoxy (Great Planes #GPMR6045)
❏
30-Minute Epoxy (Great Planes #GPMR6047)
❏
Hand or electric drill
❏
Hobby saw (razor saw)
❏
Hobby knife, #11 Blades
❏
Common pliers
❏
Screwdrivers (phillips and flat blade)
❏
T-Pins
❏
String
❏
Straightedge with scale
❏
Masking tape (required for construction)
❏
Sandpaper (medium grit)
❏
T-Bar sander (or similar)
❏
Isopropyl rubbing alcohol (70%)
❏
Round file
❏
Felt-tip pen
❏
Mixing sticks
❏
Drill Bits: 1/16", 3/32", 5/64", 5/32", 7/64"
Building Supplies and Tools
Required Accessories
PREPARATIONS
Engine Selection
The recommended engine size range is as follows:
.40 to .51 cu. in. 2-stroke
.52 to .70 cu. in. 4-stroke
The Easy Sport 40 will fly well with any of the recommended
engine sizes. For “Hot Dogging” and speedy performance,
we suggest either an O.S.
® .46 FX or a SuperTigre ™ GS-45,
both 2-stroke engines. An O.S. FS-70 Surpass is a good
choice for those who prefer 4-stroke engines.
DECISIONS YOU MUST MAKE
NOTE: We, as the kit manufacturer, can provide you
with a top quality kit and great instructions, but ultimately
the quality of your finished model depends on how you
build it; therefore, we cannot in any way guarantee the
performance of your completed model, and no
representations are expressed or implied as to the
performance or safety of your completed model.
PRECAUTIONS
3