Interrupting play, Stopping play, Changing the playing time information – Philips CDC 745 User Manual
Page 12: Playback
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
PLAYBACK
m
<Q
c5'
3T
Notes:
•
Playback will continue from the first track of
"€>" to the last track of
When all the tracks have been played, the CD
player stops with
•
To change the CDs during PLAYBACK, press
OPEN'CLOSE.
-
The CD tray open and the three CDs out
side can be changed without interrupting
playback.
Interrupting play
•
Press PAUSE.
-
The display shows PAUSE.
•
Press PLAY*REPLAY if you want to resume
playback.
-
PAUSE goes out.
Stopping play
•
Press STOP*CLEAR if you wish to stop play.
The disc and track number which can be played
will now appear in the display.
•
Press OPEN'CLOSE to remove the CDs.
Changing the playing time information
•
Press TIME on the unit if you want to see the
remaining playing time of the track being played
(REM(aining) TRACK TIME).
•
Press TIME again if you want to know the
remaining playing time of the entire CD (TOTAL
REM(aining) TIME).
•
Press TIME once more if you want to return to
the elapsed playing time of the current track
(TRACK TIME).
Note:
This does not apply for CD with more than 29 tracks
title.
Selecting
a
different
disc
during
play
(DISC SE
LECT)
•
Key in the desired CD number on the unit or
press DISC on the remote control.
-
The player will stop playing and
I will start to flash indicating the
order of discs are being switched to the
number selected.
The disc position indicator (if DISC 1 is
chosen, flashes) will appear in the CD
display. Shortly afterwards the first track of
the chosen disc will start to play.
Notes:
•
If you select a non-existent number,
lights up.
will
Selecting a different track during play (0-9)
•
Key in the desired track number (on the current
CD); two digits number must be keyed in within
2 seconds otherwise the CD player will start
playback with the first number keyed in.
-
Shortly after this, the chosen track will start
playing.
You can also select the required number by pressing
M PREVIOUS NEXTW until the required track number
appears in the display.
Searching for a passage during play
•
Hold <M SEARCH » pressed down to search for
the required passage. If you release the button,
play will continue.
Note:
The searching speed is determined by the length of
time the key is pressed:
-
the first 2 seconds fairly slowly, with low level of
volume.
-
then at the maximum speed, with no sound
output.
The volume will automatically return to its normal
level when the search button is released.
Repeating A CD
•
During play, press REPEAT. The REPEAT DISC
indicator lights up.
-
The current CD is played and then repeated.
•
Press REPEAT twice, to stop the repeat function.
Repeating ALL CDs
•
Press REPEAT twice before or during playback.
REPEAT will appear on the display.
-
All 5 discs are played and then repeated.
•
Press REPEAT again, to stop the repeatfunction.
-
The REPEAT indicator light goes out.
-
Play continues as normal.
introductory Play
The Introductory play function can be used in both
STOP and PLAY modes by pressing the SCAN
button. The SCAN function causes the first 10
seconds of every track on all CDs to be played (If CD
is already in PLAY mode, only the first 10 seconds of
the remaining tracks are played). After playing the
opening seconds of a track, the CD player jumps to
the beginning of the next track. The corresponding
track number appears in the display.
•
Press SCAN on the unit or on the remote control.
-
If the CD tray is open, it will close and the
introductory play will begin.
-
SCAN lights up and the first 10 seconds of
each track on the discs will be played. (The
seconds
are
counted
down
under
REM(aining) TRACK TIME.
10