Philips FW-C100 - Manual (Page 28)

TIMER SLEEP TIMER
Press CLOCK'TIMER again to
store the setting.
The dock starts.
• To exit without storing the setting,
press ■ on the system.
Notes:
- During dock setting if no button is
pressed within 90 seconds, the system
will exit clock setting mode
automatically.
- When a power interruption occurs, the
dock setting is erased.
Timer Setting
• The system can switch on to CD or
TUNER mode automatically at a
preset time. It can serve as an alarm
to wake you up.
• Before setting the timer make sure
the clock is set correctly.
• The timer will always be switched on
once it is set
• The volume of the timer will
increase from the minimum
level to the most recently
selected volume level.
1 Press and hold CLOCK*TIMER
for more than two seconds to
select timer mode.
fu__ or Uij___________
starts flashing."" " ^" "" is “ Ic? ^OD
am " or " uu •■[]□” or the last timer
setting, depending on whether 12-
or 24-hour mode has been
selected.
-*■ The TIMER starts flashing.
2 Press CD or TUNER to select the
desired source.
-*■ ‘Tu__ " ” ” "" indicates the Tuner
mode is selected.
“CD--“ " -iwi" indicated the CD
mode is selected.
• Before selecting CD, make sure a disc
is loaded in the CD changer tray.
3 Press ◄◄ or ►► on the system to set
the hour for the timer to start.
4 Press M or M on the system to set
the minute for the timer to start.
5 Press CLOCK*TIMER to store
the start time.
-*■ The timer is now set
The TIMER remains on the display.
• At the preset time, the timer will be
activated.
-*■ The selected source will be
played.
Notes:
- During timer setting. If no button is
pressed within 90 seconds, the system
will exit timer setting mode
automatically.
- If the source selected is TUNER, the
last tuned frequency will be switched
- If the source selected is CD, playback
will begin with the first track of the
selected disc or program. If the CD
trays are empty, the TUNER will be
selected Instead.
- The timer will not activate if a recording
is in progress.
To switch off theTIMER
1 Press and hold CLOCK-TIMER
for more than two seconds.
2 Press ■ on the system to cancel the
timer
-- The timer is now switched off.
— The display will show "OrP' and
the TIMER disappears.
To start theTIMER again (for the
same preset time and source)
1 Press and hold CLOCK-TIMER
for more than two seconds.
2 Press CLOCK-TIMER again to
store the start time.
— The timer is now on.
— The TIMER appears on the display.
Sleep Timer (only on remote
control)
This feature allows you to select a
length of time after which the system
will switch to the standby mode
automatically.
1 Press SLEEP on the remote control
repeatedly to select a period of time.
— The selections are as follows (time
in minutes): !5 — 3u — M5 — 50
-OFF - 15 ...
— "5LFFP )wF' or "OFF" will be
d i s p l a y e d . i s the time in
minutes.
2 When you reach the desired length
of time, stop pressing the SLEEP
button.
— The SLEEP display lights up.
— The Sleep Timer is now set. Before
the system switches to standby
mode, a countdown of 10
seconds will be displayed.
"BLEEP lO" - "BLEEP 3".... -
"BLEEP ¡"-"BLEEP"
While SLEEP mode is activated
- Press SLEEP once to view the
remaining length of time.
- Press SLEEP twice to change the
pre-selected period of time.
— The display will show the
remaining time followed by the
sequence of sleep timer options.
To switch off the Sleep Timer
- Press SLEEP repeatedly until "OFF"
is displayed, or press the
STANDBY-ON button.
pg 01-28/C100/37-EnN 12/6/00, 2:07 PM 3139 115 20881 (ENG)