Jaypro Sports 996 - Manual (Page 2)

ITEM QTY PART # DESCRIPTION
1 1 996U UPRIGHT (4 1/2 in OD)
2 1 VARIOUS BACKBOARDS
3 1 VARIOUS GOALS
4 3 BRC45 4 1/2 OD BAND CLAMP
5 2 SR5370 850RB-BB MOUNTING TAB
6 2 BRC30 1.315 DIA BB BRACE
7 1 SR5368 TAB PERF BOARD
ITEM QTY PART # DESCRIPTION
8 2 HS287 3/8"-16 x 1 1/4" HEX HEAD CAP SCREW
9 2 HB5031A 3/8-16 x 1 1/2 in CARRIAGE BOLT
10 2 HN5040 3/8-16 TEE NUT
11 6 HW2050 3/8 in ID FLAT WASHER
12 8 HW334
13 8 HN264 3/8"-16 HEX NUT, ZP
14 4 HS288 3/8"-16 x 1 1/2" HEX HD CAP SCREW ZP
2 4 of Page
MODEL 996
4 1/2 in ROUND POST 4 FOOT EXTENSION,
DIRECT MOUNT
BEFORE YOU START
A) UNPACK ALL PARTS AND CHECK AGAINST PARTS LIST TO ENSURE THAT ALL PARTS HAVE BEEN INCLUDED.
B) INSPECT FOR DAMAGE, REPORT ALL DAMAGES TO TRUCKING COMPANY.
UPRIGHT INSTALLATION
1) CHECK LOCAL BUILDING CODES BEFORE STARTING THE FOOTING, AS BUILDING CODES MAY VARY. LOCAL
BUILDING CODES SHOULD BE ADHERED TO IF REQUIREMENTS ARE GREATER THAN THOSE OUTLINED HERE.
2) DIG HOLE 30 INCHES SQUARE OR ROUND TO A DEPTH OF 54 INCHES, POUR A 6 INCH FOOTING AND ALLOW TO
FULLY CURE OR PLACE UPRIGHT ON TWO 6 INCH CONCRETE BLOCKS.
3) ATTACH THE TWO ANTI-ROTATIONAL BAND CLAMPS TO THE BOTTOM OF THE LOWER PORTION OF THE
UPRIGHT. THE BAND CLAMPS SHOULD BE EMBEDDED AT LEAST 6 INCHES INTO THE CONCRETE TOP AND
BOTTOM BUT NO CLOSER THAT 12 INCHES APART.
4) POSITION AND SQUARE THE UPRIGHT ONTO THE FOOTING BASE. POUR THE REMAINDER OF THE FOOTING.
ALLOW THE CONCRETE TO FULLY CURE, PER MANUFACTURERS INSTRUCTIONS, BEFORE ATTACHING
BACKBOARD AND GOAL. NOTE THE TOP HOLE OF THE BACKBOARD MOUNTING PLATE SHOULD BE 119 INCHES
OFF THE PLAYING SURFACE.
FINAL ASSEMBLY
5) ATTACH THE APPROPRIATE BRACE MOUNTING BRACKET TO THE BACK OF THE BACKBOARD, AS SHOWN IN
DETAIL D. THE BRACKET WILL DEPEND ON THE BACKBOARD ORDERED. THE BRACKETS WILL EITHER BE
INCLUDED WITH THE BACKBOARD OR FOUND IN THE GENERAL KIT. THE SPACING BETWEEN THE RIGHT ANGLE
BRACKETS OF THE RECTANGULAR STEEL BACKBOARD IS APPROXIMATLY 36 INCHES. (FAN BOARDS DO NOT
REQUIRE REAR BRACING)
6) LIFT AND ATTACH THE BACKBOARD TO THE MOUNTING PLATE USING ONLY THE TOP TWO FASTENERS AND
TEE NUTS SHOWN IN SECTION A-A. WHEN THE BACKPOARD IS INSTALLED THE TEE NUTS SHOULD BE UP
AGAINST THE BACKBOARD AS SHOWN IN DETAIL B. THE USE OF THE TEE NUTS ALLOW FOR EASY
REPLACEMENT OF THE GOAL. ( IF INSTALLING A FAN BOARD SKIP AHEAD TO STEP 10)
7) INSTALL THE BAND CLAMP TO THE UPRIGHT PIPE BY FIRST SPREADING THE BAND CLAMP OPEN ONLY
ENOUGH TO GET IT ONTO THE UPRIGHT. SEE DETAIL F
8) WITH THE HELP A C-CLAMP CLOSE THE BAND CLAMP BACK DOWN AND HOLD CLOSED BY INSTALLING ONLY
THE LOWER BOLT AND NUT FASTENERS. THE BAND CLAMP NEEDS TO BE APPROXIMATLY 19 INCHES FROM THE
BACK SIDE OF THE BACKBOARD
9) INSTALL THE 1-5/16 DIA SUPPORT BRACES TO THE BACKBOARD AND BAND CLAMP AS SHOWN IN THE DETAILS
E AND F.
10) PLUMB AND LEVEL THE BACKBOARD BEFORE TIGHTENING THE HARDWARE.
11) FINALLY ATTACH THE GOAL WITH THE REMAINING HARDWARE SHOWN IN SECTION A-A, MAKE CERTAIN THAT
A WASHER IS PLACED BETWEEN THE GOAL AND THE LOWER HOLES IN ORDER TO KEEP THE GOAL
PERPANDICULAR WITH THE BACKBOARD. NOTE THE ORIENTATION OF THE LOWER TWO BOLTS. FOR ADDED
SAFETY, THE EXPOSED THREADS AND NUTS SHOULD BE PLACED ON THE BACKSIDE OF THE BACKBOARD, AS
SHOWN IN SECTION A-A AND DETAIL C.
TOOLS REQUIRED
9/16 in Socket Wrench and Combination Wrench
Optional 4 inch C-Clamp
T:\Aftermarket\Basketball\996\996 INSTALLATION MANUAL\996 INSTALL (REV B SHORTENED MAST JUNE 2010) PAGE 2 (copy).idw UPDATE 5/01/13