Panasonic SPX900 - Manual (Page 100)

100
8-4 VF
8-4-1 VF DISPLAY 8-4-2 VF MARKER
8-4-3 USER BOX
The ____ in the Adjustable Range column indicates the preset
mode.
Items/
Data Saved
Adjustable
Range
Remarks
DISP
CONDITION NORMAL
HOLD NORMAL: Display status constantly.
HOLD:
Display status only when the
MODE CHECK switch is pressed.
– C U F E
DISP MODE 1
2
3 Set the DISP MODE.
Switch the camera’s Warning/Message
indication. Please refer to [4-7-4 Display
Modes and Setting Changes/adjustment
Result Messages] for more information.
– C U F E
VF OUT Y
NAM
R
G
B Select the VF output.
Y:
Brightness signal
NAM: Output signal with the highest level
among R, G, and B signals.
R: Rch signal
G: Gch signal
B: Bch signal
– C U F E
VF DTL 0
:
3
:
5
Select the VF DTL.
Additionally enhance the DTL for the VF
signal. 0 setting is the same DTL as the
primary scan lines.
– C U F E
ZEBRA1
DETECT 0%
:
70%
:
109%
Set the ZEBRA1 detection level (IRE value).
– C U F E
ZEBRA2
DETECT 0%
:
85%
:
109%
Set the ZEBRA2 detection level (IRE value).
– C U F E
ZEBRA2 ON
SPOT
OFF Set the ZEBRA2 to ON, OFF, or SPOT.
– C U F E
LOW LIGHT LVL OFF
10%
15%
20%
25%
30%
35%
Set the camera incoming light volume at
which to display LOW LIGNT.
– C U F E
ECU MENU
DISP. ON
OFF Set the menu display on the VF to ON or
OFF when the ECU is connected.
– C U F E
50M
INDICATOR ON
OFF Set the 50M recording indication to ON or
OFF.
– C U F E
MARKER/CHAR
LVL 50%
60%
70%
80%
90%
100% Adjust the brightness of markers and
characters displayed on the VF.
– C U F E
Items/
Data Saved
Adjustable
Range
Remarks
TABLE A
B Select the VF MARKER setting table.
First, select table A or B, then set the items
below for each table.
– C U F E
CENTER MARK OFF
1
2
3
4
Switch the center mark.
OFF: Do not display center mark.
1:
+ (large)
2: Hollow (large)
3: + (small)
4: Hollow (small)
– C U F E
SAFETY ZONE OFF
1
2
Select the frame type for the safety zone.
OFF: Do not display frame.
1:
Box
2: Corner frame
– C U F E
SAFETY AREA 80%
:
90%
:
100%
Set the position of the safety zone.
– C U F E
FRAME SIG 4:3
13:9
14:9
VISTA Set the frame marker.
Only enabled when REC MODE is set to
16:9.
The VISTA ratio is 16:8.65.
– C U F E
FRAME MARK ON
OFF
Set the frame marker to ON or OFF.
– C U F E
FRAME LVL 0
:
15
Set the level outside the frame marker.
0:
Equivalent to signal OFF.
15: Same brightness as center area.
This setting, however, is disabled if
the FRAME SIG is set to VISTA.
– C U F E
Items/
Data Saved
Adjustable
Range
Remarks
USER BOX ON
OFF Select whether or not to display the USER
BOX.
– C U F E
USER BOX
WIDTH 1
:
13
:
100
Set the width of the USER BOX.
– C U F E
USER BOX
HEIGHT 1
:
13
:
144
Set the height of the USER BOX.
– C U F E
USER BOX H
POS –50
:
+00
:
+50
Set the horizontal position of the USER
BOX.
– C U F E
USER BOX V
POS –144
:
+000
:
+144
Set the vertical position of the USER BOX.
– C U F E