G-Shock G-9300 - Manual (Page 8)

Operation Guide 3261 3281
E-70
Moon
Phase
Indicator
Moon Phase
Moon Age
Module
3261
Module
3281
25.0-26.8 13.9-15.7 15.8-17.5 17.6-19.4 19.5-21.2 21.3-23.1 23.2-24.9 26.9-28.6
Full
Moon Last
Quarter
(Waning)
Moon phase (part you can see) (part you cannot see)
E-71
Checking the Current Time in a Different Time Zone
You can use the World Time Mode to view the current time in one of 31 time zones (48
cities) around the globe. The city that is currently selected in the World Time Mode is
called the “World Time City”.
To enter the World Time Mode
Use
D to select the World Time Mode (WT) as shown on
page E-22.
• Entering the World Time Mode will cause WT to be
displayed for the mode name for about one second, and
then the name of the currently selected city will scroll on the
display. After that, the city code will be displayed. If you
select a different city, the city name will scroll first and then
the city code will appear. For information about city codes,
see the “City Code Table” at the back of this manual.
• To view the name of the currently selected city, press
A in the World Time Mode. This will cause the city
name to scroll on the display.
Currently selected
World Time City
Current time in the
currently selected
World Time City
llllllllll
Currently selected
World Time City
Current time in the
currently selected
World Time City
llllllllll
E-72
To view the time in another time zone
In the World Time Mode, use
E (East) to scroll through city names.
• Pressing E and B at the same time will jump to the UTC time zone.
To specify standard time or daylight saving time (DST) for a city
1. In the World Time Mode, use E (East) to display the
city name (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A to toggle between Daylight Saving Time
(DST indicator displayed) and Standard Time (DST
indicator not displayed).
• The DST indicator is shown on the World Time
Mode screen while Daylight Saving Time is turned
on.
• Using the World Time Mode to change the DST
setting of the city name that is selected as your
Home City also will change the Timekeeping Mode
time DST setting.
DST indicator
llllllllll
DST indicator
llllllllll
E-73
• Note that you cannot switch between standard time/daylight saving time (DST)
while UTC is selected as the World Time City.
• Note that the standard time/daylight saving time (DST) setting affects only the
currently selected time zone. Other time zones are not affected.
E-74
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two finishes.
To enter the Stopwatch Mode
Use
D to select the Stopwatch Mode (STW) as shown on
page E-22.
• About one second after STW appears on the display,
the display will change to show the stopwatch hours.
To perform an elapsed time operation
E E E E A
Start Stop (Restart) (Stop) Reset
Hours
1/100 second
Seconds
Minutes
Current time Hours
1/100 second
Seconds
Minutes
Current time
E-75
To pause at a split time
E A A E A
Start Split
(SPL displayed) Split release Stop Reset
To measure two finishes
E A E A A
Start Split
First runner
finishes.
Display time of
first runner Stop
Second runner
finishes. Split release
Display time of
second runner Reset
E-76
Note
• The Stopwatch Mode can indicate elapsed time up to 999 hours, 59 minutes, 59.99
seconds.
• Once started, stopwatch timing continues until you press A to stop it, even if you
exit the Stopwatch Mode to another mode and even if timing reaches the stopwatch
limit defined above.
• Exiting the Stopwatch Mode while a split time is frozen on the display clears the
split time and returns to elapsed time measurement.
E-77
Using the Countdown Timer
The countdown timer can be configured to start at a preset time, and sound an alarm
when the end of the countdown is reached.
To enter the Countdown Timer Mode
Use
D to select the Countdown Timer Mode (TMR) as
shown on page E-22.
• About one second after TMR appears on the display,
the display will change to show the countdown time
hours.
Current time
Countdown time
(Hour, minutes, seconds)
Current time
Countdown time
(Hour, minutes, seconds)
E-78
To specify the countdown start time
1. Enter the Countdown Timer Mode.
• If a countdown is in progress (indicated by the seconds counting down), press
E to stop it and then press A to reset to the current countdown start time.
• If a countdown is paused, press A to reset to the current countdown start
time.
2. Hold down A until the hour setting of the current countdown start time starts to
flash. This is the setting screen.
3. Press D to move the flashing between the hour and minute settings.
4. Use E (+) and B (–) to change the flashing item.
• To set the starting value of the countdown time to 24 hours, set 0H 00’00.
5. Press A to exit the setting screen.
E-79
To perform a countdown timer operation
E E E E A
Start Stop (Restart) (Stop) Reset
• Before starting a countdown timer operation, check to make sure that a countdown
operation is not in progress (indicated by the seconds counting down). If it is, press
E to stop it and then A to reset to the countdown start time.
• An alarm sounds for ten seconds when the end of the countdown is reached. This
alarm will sound in all modes. The countdown time is reset to its starting value
automatically when the alarm sounds.
To stop the alarm
Press any button.