O.S. Engines GT60 - Manual (Page 4)

Copyright 2012 by O.S. Engine Mfg. Co., Ltd. All rights reserved. C 60092770 051404
O.S. GENUINE PARTS & ACCESSORIES
(72403050)
(79870050)
(55500004)
(71531010)
(L)
M5
BLIND NUT (10pcs.)
LOCK WASHER (10sets)
M5
NON-BUBBLE WEIGHT
(S)
(72403051)
SUPER FILTER
The specifications are subject to alteration for improvement
without notice.
Dimensions (mm) THREE VIEW DRAWING
http://www.os-engines.co.jp
ENGINE EXPLODED VIEW
Type of screw
C...Cap Screw
ENGINE PARTS LIST
6-15 3-Chome Imagawa Higashisumiyoshi-ku
Osaka 546-0003, Japan TEL. (06) 6702-0225
FAX. (06) 6704-2722
The specifications are subject to alteration for improvement
without notice.
Cylinder Block
Piston Ring
Piston
Piston Pin
Piston Pin Retainer
Connecting Rod
Cylinder Gasket
Pilot Shaft
Drive Spacer
Taper Collet
Parallel Key
Ball Bearing (F)
Front Housing
Rotation Sensor
Rotation Sensor Retaining Screw Set (2pcs.)
Ball Bearing (R)
Specifications
Displacement
Bore
Stroke
PracticalR.P.M.
Output
Weight (Engine)
(Silencer)
59.91 cc / 3.656 cu.in.
44.0 mm / 1.732 in.
39.4 mm / 1.551 in.
1,600-8,000 r.p.m.
6.08 ps / 6.00 hp / 8,000r.p.m.
1.400 g / 49.38 oz.
178.0 g / 6.28 oz.
105.0 g / 3.70 oz. (Ignition module)
M5 STAND OFF ENGINE MOUNTS
(S)
(4pcs.)
(74003530)
(74003540)
M5 Stand Off Engine Mount 1/4" (6.4mm)
M5 Stand Off Engine Mount 1/2" (12.7mm)
M5 Stand Off Engine Mount 3/4" (19.1mm)
M5 Stand Off Engine Mount 1" (25.4mm)
M5 Stand Off Engine Mount 1-1/4" (31.8mm)
M5 Stand Off Engine Mount 1-1/2" (38.1mm)
M5 Stand Off Engine Mount 1-3/4" (44.5mm)
M5 Stand Off Engine Mount 2" (50.8mm)
(74003510)
(74003520)
(74003580)
(74003570)
(74003560)
(74003550)
28602000
28602200
28614100
28601800
28615100
28616000
28681000
22081408
29781350
74002310
71669010
28625000
29714300
79871550
29709000
79871545
28603100
28603400
28603200
29706000
29717000
28605000
28614000
28602100
28608000
29708100
29708200
29730000
28601600
74002320
74002321
28631000
CAP SCREW SETS (10pcs./sets)
Code No. Size
Cylinder Block Retaining Screw (4pcs.)
Rear Housing Retaining Screw (4pcs.)
Caburetor & Reed valve Retaining Screw (2pcs.)
Pcs. used in an engine
79871415
79871520
79871560 M4x15
M5x20
M5x60
No. Code No. Description No. Code No. Description
Crankshaft
Crank Pin Stop Screw
Case Gasket
Rear Housing
Carburetor & Reed Valve Gasket Set (1piece each)
Reed Valve Assembly
Carburetor Complete (HAD313)
Throttle Valve Lever (No.5)
N4-40x5 Screw (1pc.)
Ignition Module (IG-02)
Spark Plug CM-6 (Rcexl)
E-6020 Silencer
Exhaust Gasket
Cap Screw M5x50 (10pcs./set)
Propeller Washer
Cap Screw M5x45 (10pcs./set)
14
15
16
17
18
19
20
20-1
20-2
1
2
3
4
5
6
7
8
9
9-1
9-2
10
11
12
12-1
13
After cleaning the engine, dry it well then inject a
small quantity of oil used to mix fuel and rotate the
crankshaft several times to distribute the oil well
inside the engine. Finally reassemble the engine
and store it in a dry place after inserting it in a heavy
vinyl bag.
When the engine is not to be used for a long period
(more than a year), remove the engine from the
model, clean the outside then remove the
carburetor, and plug all tubing. Clean inside the
engine by rotating the crankshaft with the engine
immersed in container filled with gasoline.
Also use gasoline to clean the outside of the
carburetor.
Clean the outside only because the inside parts are
sensitive to foreign substances.
SPARK PLUG CM-6 (NGK) (71669000)
(28382100)
ID. 2mm × OD. 4mm Length 500mm
(28382200)
ID. 3mm × OD. 5mm Length 500mm
FLUORORUBBER TUBE
5
C.M4x15
1
2
3
4
6
7
8
9
10
11
12
13
14
16 15
17
19
20
12-1
18 C.M5x50
M5
9-1 9-2
20-1
20-2
C.M5x60
C.M5x20
43
72
56
86
43 43
120
70
40
20 20
2-M5
69.5
127.6
36 91.6
38.8
43
132.2
42.8
85.6
39
39
33
66
33
PCD 30
4-M5
4- 5.5
39
78
97.6