Philips Norelco Multigroom 3300 Series 3000 grooming kit QG3331-42 6 tools for all-in-one styling 18 built-in length settings 35mins cordless use-10h charge Hair clipper attachment - Manual

ENGLISH
IMPORTANT
SAFETY
INSTRUCTIONS
When using an electric appliance, basic precau­
tions should always be followed, including the
following;
Read all instructions before using this
appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for Groomer while plugged
in that has fallen into water. Unplug
immediately.
2. Use Groomer only in dry condition. Do
not use Groomer while bathing or in a
shower.
3. Do not submerge Groomer in water.
4. Do not place or store Groomer where it can
fall or be pulled into a tub or sink. Do not
place or drop Groomer into water or other
liquid while plugged in.
5. Always unplug the Groomer from the
electrical outlet immediately after use,
except when Groomer is (re)charging.
6. Remove power supply cord from Groomer
before cleaning.
7. When discarding Groomer, unplug Groomer
before removing rechargeable batteries. See
Battery Removal instructions.
WARNING
To reduce the risk of burns, fire, electric
shock or injury to persons:
1. Close supervision is necessary when this
Groomer is used by, on, or near children or
invalids.
2. Use this Groomer for its intended household
use as described in this manual. Do not use
attachments not recommended by Philips
Electronics North America Corporation.
3. Never operate this Groomer if it has a
damaged cord or charging plug, if it is not
working properly, if it has been dropped or
damaged, or dropped into water. For
assistance call I-800-243-3050.
4. Keep the Groomer, cord and charging plug
away from heated surfaces.
5. Never drop or insert any object into any
opening.
6. Never operate the Groomer with the air
openings blocked or while on a soft surface,
such as a bed or couch, where the air
openings may be blocked. Keep the air
openings free of lint, hair, and the like.
7. Do not operate, charge or plug in
Groomer outdoors or where aerosol
(spray) products are being used or where
oxygen is being administered.
8. Always check foil, cutters, trimmers and
combs before using the Groomer. Do not
use the Groomer if foil, cutters, trimmers
or combs are damaged, as injury may occur.
9. Always attach plug to Groomer first,
then charging plug into outlet.To disconnect,
remove charging plug from outlet.
10. Use only the cord provided to charge and
Features
(re)charge the Groomer.
1. If tne applia 11. If the appliance is subjected to a major
change in temperature, pressure or
humidity, let the appliance acclimatize for
30 minutes before using.
12. Never put the Groomer in direct sunlight or
store at a temperature above 140°F.
13. To prevent possible damage to the cord, do
not wrap cord around the Groomer.
14. Only use the power plug and other
accessories supplied with the Groomer.
SAVETHESE
INSTRUCTIONS
IMPORTANT: The power plug contains
a transformer. Do not cut off the power
plug to replace it with another plug as this
will cause a hazardous condition.
Registration
Congratulations on your purchase and welcome
to Philips Norelco!
To fully benefit from the support that Philips
Norelco offers, register your product at
www.norelco.com/register
You may be eligible for an extended warranty
of an additional 6 months for 2 1/2 years total.
To register your product go to www.norelco.
com/register. Keep your proof of purchase for
warranty entitlement.This offer is available
online CDNLY and expires 12/31/16.
A
B
C
D
E
F
G
H
K
L
M
N
Full-size Trimmer
Handle
On/Off Switch
Storage Tray
Nose/Ear Hair Trimmer
Precision Trimmer
Beard and Stubble Comb
Detail Comb (QG3331 only)
Hair Clipper Comb
Body Comb (QG3331 only)
Guiding Grooves
Hair Length Setting Indicator
Storage Pouch (QG3331 only)
Adapter
Full Two-Year Warranty
45-Day Money-Back Guarantee
The tap symbol on the
groomer indicates that the
groomer can be rinsed under
running tap water.
Put It To The Test
Like many new products, your Philips Norelco
Grooming Kit may take a little getting used to. If you
are using an electric Groomer for the first time, or
if you’ve been using a different brand, take the time
to acquaint yourself with your new Grooming Kit.
Your Grooming Kit features a full size trimmer with
all the attachments to make trimming facial hairs or
hair clipping goof proof
Throw your scissors away and put your new
Grooming Kit to the test. We guarantee precise,
professional results or Philips Norelco will refund
you the full purchase price as long as the request
is received within 45 days of purchase.
To Charge/Recharge
> Fully charge Groomer before using for the first
time or after non-use for a long period of time.
> Charging, recharging or using Groomer at
temperatures below 40°F or higher than 95'F
adversely affects lifespan of the battery.
0 Be certain Groomer is OFF.
B Connect appliance plug directly into the
Groomer. Plug adapter into any 120VAC
outlet (Fig. 1). Use only the cord provided.
B The charging light on the adapter will light
to indicate the Groomer is charging.
> It will take approximately 10 hours to fully
charge the Groomer for a cordless trimming
time of up to 35 minutes.
> You can charge the Groomer for 16 hours
for a cordless trimming time up to 45 minutes.
> The charging light does not turn OFF after
Groomer is fully charged.
Q Disconnect the cord and unplug from
electrical outlet.
Optimize the working life of the battery
t After the Groomer has been charged for
the first time, do not recharge the Groomer
between grooming sessions. Continue using it
until the battery is completely empty.
1 Do not charge for more than 24 hours.
t Do not keep cord permanently plugged in.
I Discharge/run down the battery completely
twice a year by letting the motor run until it
stops.
I If the Groomer hasn’t been used for a long
period of time, it must be recharged for a
full 10 hours.
Cordless Trimming
D Charge according to directions. Unplug
Groomer from outlet and remove cord.
B Slide ON/OFF switch ON to begin trimming.
B When finished, turn Groomer OFF.
Hair Clipping
► Use this Groomer for its intended household
use as described in this manual.
► Make sure that the Groomer is fully charged
before you start clipping. This Groomer will
not operate while cord is connected to
electrical outlet.
► Before you start clipping, make sure that the
head of the person whose hair you are cutting
is at the same level as your chest so that all
parts of his/her head are clearly visible and
within easy reach.
► Make sure hair is clean and dry.
I Before you begin, comb the hair in the
direction of growth (Fig. 2).
► To achieve optimal clipping results, always move
the appliance slowly through the hair against
the direction of hair growth.
Do not move the Groomer too fast. Make smooth
and gentle movements.
Clipping with hair clipper comb
D Put the full-size trimmer on Groomer handle
(1) and turn clockwise (2) to lock in place
(Fig-3).
B Slide the hair clipping comb into the guiding
grooves on both sides of Groomer handle
(Fig. 4).
B Press the Hair Length Setting Selector (1)
and slide the comb to the desired hair length
setting (2) (Fig. 5).
The hair clipping comb has 18 length settings and
cuts hair to a length of 1/8 - 25/32 in. (3-20mm).
□ The setting selected will appear on the back
of the Groomer.
When you are clipping for the first time, start
at the maximum clipping length setting (#20) to
familiarize yourself with the appliance and pre­
vent accidentally trimming hairs too short. As you
become familiar with the settings, adjust the Hair
Length Setting Selector to desired trimming length.
Selector will 'click' into position at each setting.
B Switch the Groomer ON (Fig. 6).
Q Make sure that the flat part of the comb is
always in full contact with the scalp to obtain
an even result (Fig. 7).
B Move the appliance slowly over the crown
from different directions to achieve an even
result (Fig. 8).
fil Always move the appliance against the
direction of hair growth. Press lightly.
□ Make overlapping passes over the head to
ensure that all hair that should be cut has
been cut.
EE Turn the Groomer off and remove the hair
clipper comb often to blow and/or shake
out hair that has accumulated.
> REMEMBER;You must reset the hair length
selector back to your desired setting every
time you replace the hair clipper comb on the
appliance.
TIP:Write down the settings you have used to create
a certain hairstyle as a reminder for future clipping
sessions.
Contouring without the hair clipper
comb
I Use the Groomer without a comb to clip hair
very close to the skin (3/64in./1mm) or to
contour the neckline and area around the ears.
o
Remove the hair clipper comb by pressing
the Hair Length Setting Selector (1) and
slide the comb upwards (2). Pull comb off
Groomer (Fig. 9).
Be careful when you are clipping without comb
attachment as when the Groomer is turned on it
will remove every hair it touches.
B To contour the hairline around the ears,
comb the hair ends over the ears.
B Tilt the Groomer in such a way that only
one edge of the cutter blades touches the
hair ends when you shape the contours
around the ears (Fig. 10).
Only cut the hair ends.The hairline should be
close to the ear.
□ To contour the nape of the neck or
sideburns, turn the Groomer and hold it with
the cutter blades pointing downwards
(Fig. 11).
B Move the Groomer slowly and smoothly
following the natural hairline.
Beard and Stubble Trimming
> Always comb your beard and/or moustache
with a fine comb before you start trimming.
• If you are trimming for the first time, be
careful. Do not move the Groomer too fast.
Make smooth and gentle movements.
> After trimming, residual hair length can vary
depending on hair type.
Beard Trimming With Beard and
Stubble Comb
* •
• Use the beard and stubble comb to trim your
beard and moustache to different lengths.
> Trimming is easier when the skin and hair
are dry.
k The hair length settings are indicated on the
Groomer.The settings correspond to the
remaining hair length after trimming.
• The beard and stubble comb cuts hair to a
length of 3/64 - 23/32 in. (1-18 mm).
B Ptit the full-size trimmer on Groomer handle
(1) and turn clockwise (2) to lock in place
(Fig. 3).
B Slide the beard and stubble comb into the
guiding grooves of the Groomer (Fig. 12).
B Press the setting selector (1) and slide the
comb to the desired hair length setting (2)
(Fig. 13).
> If you are trimming for the first time, start by
using the maximum trimming length setting
of 23/32 in. (18mm) to prevent accidentally
trimming hairs too short. As you become
familiar with the settings, adjust the comb
to desired trimming setting.
D Slide the On/Off switch ON to begin
trimming (Fig. 6).
B To trim in the most effective way, move the
Groomer against the direction of hair
growth. Do not move the Groomer too
fast. Make smooth and gentle movements and
make sure the surface of the trimming comb
always stays in contact with the skin.