Philips Norelco Do-It-Yourself clipper DIY cordless hair clipper QC5580-40 Easy Reach 180° rotating head 14 built-in length settings 60mins cordless use-1h charge Head shave attachment - Manual (Page 2)

D To contour the hairline around the ears,
comb the hair ends over the ears.
a Press the ON/OFF Button to turn on the
appliance.
D Tilt the Clipper in such a way that only one
edge of the cuttiing element touches the hair
ends. Be careful not to trim too much. The
hairline should be close to the ear (Fig. 13).
B To contour the neckline and the sideburns,
turn the Clipper and make downward
strokes (Fig. 14).
NOTE: Move the Clipper slowly and smoothly.
Simply follow the natural hairline.
Q Adjust the position of the rotating head to
make contouring easier.
Shaving
TIP: Shaving is easier when the hairs are shorter
than 1mm. If the hairs are longer than 1mm, use
the cutting element without the comb to pre<ut
hairs to the shortest setting.
D Turn off Clipper.
H Pull the comb off the rotating head (Fig. 12).
H Press the release buttons (1) and remove
the cutting unit from the handle (2) (Fig. 15).
D Attach the shaving head by pressing it onto
the appliance.You will hear a ‘click’ (Fig. 16).
Make sure that the shaving head locks into
position properly.
a Remove the protection cap from the shaving
head (Fig. 17).
If the shaving head foil shows signs of wear or
damage, do not use as injury may occur Do not
use the shaving head until foil has been replaced.
n Adjust the position of the rotating head to
make shaving easier.You can do this before
and/or during use (Fig. 18).
Q Place the shaving head on your scalp and
start shaving (Fig. 19).
NOTE: Make sure that the shaving foil is always m
full contact with your scalp.
Cleaning
I Clean the Clipper after each use.
I Always switch Clipper OFF, unplug and remove
power supply cord from Clipper before
cleaning.
I Do not use compressed air, abrasive cleaning
agents, scourers or aggressive liquids such as
gasoline, acetone or ethereal oils to clean
the Clipper and attachments.
I Never clean, replace or remove Clipper
attachments with motor ON.
I Do not apply pressure to shaving head. Do not
touch foil with hard objects as this may dent
or damage foil or cutters. If damage occurs,
replace damaged parts.
I Do not use Clipper if foil, cutter or cutting
element are damaged or broken as injury may
occur.
I Use a soft, dry cloth to clean Clipper handle.
During Use:
I If cut hairs have accumulated in the comb
area, remove hairs by shaking, blowing or using
cleaning brush provided.
Cleaning the Cutting Element and
Combs After Each Use:
D Make sure the Clipper is switched OFF
and disconnected from the electrical outlet.
a Remove any comb attachment (Fig. 12).
B Blow and/or shake out any hair that may
have accumulated in the comb.
□ Rinse the comb under the tap or clean it
with the cleaning brush supplied.
H Apply pressure to the center of the cutting
element with your thumb (1) until it releases
from the rotating head (2) (Fig. 20).
Be careful that the cutting element does not fall to
the floor
B
Clean the cutting element under the tap
or with the brush supplied (Fig. 21).
Make sure the cutting element is thoroughly dry
before reattaching to Clipper
Cleaning the Shaving Head
D
Clean the inside of the rotating head under the
tap or with the brush supplied (Fig. 22).
B
Clean the handle and the adapter with the
cleaning brush supplied or with a dry cloth.
D Insert the notch of the cutting element into
the slot on the rotating head and push until
the cutting element‘clicks’ into place (Fig. 23).
O Turn off the Clipper and disconnect from the
electrical outlet.
a Press the release buttons on the shaving head
and remove the shaving foil from the shaving
head (Fig. 24).
B Rinse the shaving head and shaving foil under
the tap (Fig. 25).
NOTE:To dean the shaving head with the cleaning
brush, brush the inside and outside of the shaving
head and the outside of the shaving foil.To remove
cut hairs from the inside of the shaving foil, tap the
bottom of the shaving foil gently on a flat surface.
□ Press the shaving foil back into the shaving
head (Fig. 26).
Replacing the Shaving Foil Head
► If the shaving foil and cutters are worn or
damaged, do not continue using the Clipper.
Replace the shaving foil and cutters immediately.
► It is recommended that you replace your
shaving foil and cutters once a year.
IA worn or damaged shaving foil or cutters
should only be replaced with an original Philips
Norelco shaving foil, model QC5500, which is
available on the Philips Norelco website,
www.philips.com/support or call
I -800-243-3050 for assistance.
► The foil is a precision part. Handle with care.
D Turn off the Clipper and disconnect it
from the electrical outlet.
a Press the release buttons on the shaving head
and remove the shaving foil from the shaving
head (Fig. 24).
H Remove the retaining frame from the old
shaving foil (Fig. 27).
Q Place the retaining frame on the new shaving
foil (Fig. 28).
B
Remove the old shaving cutters (Fig. 29).
B
Place the new cutters on the shaving head.
You will hear a ‘click’ (Fig. 30).
Q Press the shaving foil back into the shaving
head (Fig. 26).
This Clipper has no other user-serviceable parts.
For assistance call 1 -800-243-3050.
PHILIPS
^NORELCO
Assistance
For assistance, visit our website:
www.philips.com/support or
call toll free: 1-800-243-3050
Online information is available 24 hours a day, 7
days a week.
Storage
k Be sure Clipper is turned OFF. Remove cord
from outlet and Clipper before storing in a
safe, dry location where it will not be crushed,
banged, or subject to damage.
I Do not wrap cord around Clipper when
storing.
I Store cord in a safe location where it will not
be cut or damaged.
► Do not place or store Clipper where it can fall
or be pulled into a tub or sink, water or other
liquid while plugged in.
Battery Removal
► This Philips Norelco Clipper contains a
rechargeable Lithium-Ion battery which must
be disposed of properly (Fig. 31 ).
► Battery may only be removed when Clipper is
to be discarded.
I For assistance, visit our website,
www.philips.com/support or
call toll free; 1-800-243-3050
D Unplug electrical cord from outlet and
Clipper before dismantling Clipper.
Q Allow Clipper to run until the battery is
empty/depleted.
Q Turn Clipper OFF.
Q Remove any comb attachment.
B
Remove the upper housing part of the
Clipper (Fig. 32).
B
Use a screwdriver to open the inner body
of the Clipper.
Q Use a screwdriver to remove the battery
from the Clipper (Fig. 33).
Headgroom
Pro
QC5580
Rechargeable
Cordless/Cord
Always here to help you
Register your product and get support at
www.norelco.com/register
4222 002 8312 2
B
Cut the wires with household scissors.
B Do not attempt to replace battery. Insulate
battery ends by covering with tape and/or
place battery in a small plastic bag.
EQ Discard your Clipper. Do not attempt to
plug electrical cord into the outlet or
recharge the Clipper after the battery has
been removed.
ED
Contact your local town or city officials
for battery disposal information or call
1 -800-8-BATTERY or www.rbrc.com for
battery drop-off locations.
Full Two-Year Warranty
Philips Electronics North America Corporation warrants eadi new Philips
Norelco product. Model QC5580 (except foil, cutters and combs) against
defects in materials or workmanship for a period of two years from the
date of purchase, and agrees to repair or replace any defective produa
Vifithout cn.irjje
IMPORTANT: This warranty does not cover damage resulting from
accident, misuse or abuse, lack of reasonable care, the affixing of any
attachment not provided with the product or loss of parts or subjecting
the product to any but the specific voltage.* Use of unauthorized
replacement parts will void this warranty.
PHILIPS ELECTRONICS NORTH AMERICA CORPORATION
WILL NOT PAY FOR WARRANTY SERVICE PERFORMED BY
A NON-AUTHORIZEO REPAIR SERVICE AND WILL NOT
REIMBURSE THE CONSUMER FOR DAMAGE RESULTING FROM
WARRANTY SERVICE PERFORMED BY A NON-AUTHORIZED
REPAIR SERVICE.
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL.
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/
norelco or call 1-800-243-3050 for assistance. It is suggested that for
your protection you return shipments of product by insured mail,
insurance prepaid. Damage occurring during shipnnent is not covered by
this warranty
NOTE: No other warranty, written or oral, is authorized
by Philips Electronics North America Corporation. This warranty gives
you specific legal nghts. and you may also have oUier rights which vary
from state to state. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above exclusion and
limitations nnay not apply to you.
•Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A Divisiw of Philips Electronics Nortii Amenca Corporation
RO. Box 10313. Stamford. CT 06904
This symbol on the product's nameplate means it is
usTto listed by Underwnters' Laboratories. Inc.
Noieko is a Registered Trademark of Philips Electronics
North America Corporation.
PHILIPS IS a Registered Trademark of KomnWi)ke Philips ElectronKS N.V.
© 2013 Philips Electronics Nortfi Amenca Corporation. All R^hts Reserved.
PHILIPS
^NORELCO
45-DAY MONEY-
BACK GUARANTEE
If you are not fully satisfied with your Philips Norelco
Clipper send the product back and we’ll refund you the
full purchase price.
The Clipper must be shipped prepaid by insured
mail, insurance prepaid, have the original sales
receipt, indicating purchase price and date of
purchase, and the money-back guarantee return
authorization form enclosed. We cannot be
responsible for lost mail.
The Clipper must be postmarked no later than
4S days after the date of purchase. Philips
Norelco reserves the right to verify the purchase
price of the product and limit refunds not to
exceed suggested retail price.
To obtain money-back guarantee return
authorization form, call 1-800-243-3050 for
assistance.
Delivery of refund check will occur 6-8 weeks AFTER
receipt of returned product.