PULSE ShowerSpas 1032 Hanalei - Manual (Page 3)

4 5
Assembly
After unpacking your ShowerSpa, some assembly is required prior to installation.
Shower Arm Assembly
Figure 1
1. Place the escutcheon (4) over the threaded end of the shower arm (3) and insert threaded end into shower arm outlet (5). Make
certain the threads for attaching the shower head are pointing down.
2. On the inside of the ShowerSpa, place the large rubber washer (12) over the threaded end and tighten securely with brass nut
(13)—DO NOT OVERTIGHTEN.
3. Put a rubber washer (17) into the shower arm outlet hose (6) and then tighten to the shower arm (3). Be sure to check for leaks
before completing installation.
Handheld Holder Assembly
Figure 2
1. Place the threaded end of the handheld holder (8) into the handheld outlet (10). Make certain the threads for the handheld hose
are pointing down.
2. On the inside of the ShowerSpa, place the large rubber washer (12) over the threaded end and tighten securely with brass nut (13).
3. Put a rubber washer (17) into the handheld outlet hose (11) and then tighten to the handheld holder (3). Be sure to check for leaks
before completing installation.
After The ShowerSpa Is Mounted To The Wall
Connect The Handheld Shower and Shower Head
1. Insert a rubber washer (17) into the hex end of the handheld hose (9), and attach to the handheld holder (8).
2. Place a rubber washer into the tapered end of the handheld hose and attach to the handheld shower (7). Place the tapered end of
the hose into the handheld holder.
3. Place a rubber washer (17) inside the threaded nut on top of the shower head (2) and attach to the shower arm (3).
Installation – New Construction
Extensive Remodel – New Finished Wall Surface
1. Prior to sheetrock, stub-out ½" hot and cold supply lines
beyond finished wall surface, 4½" on center. For best results,
attach 90° brass fittings (available at most hardware stores)
to the stub-outs maintaining ¼" – ½" of space between the
fitting and finished wall. The open end of the 90° brass fit-
tings should point down so the supply lines attach parallel
to the wall.
1
2. The height of the stub-outs is completely dependent upon
the desired mounting height of your Hanalei ShowerSpa. For
a person 5'8" – 6'2" we recommend the stub-outs be 35" from
finished floor.
2
3. Before installation, make certain that water is completely
turned off to both hot & cold supply lines of the shower.
4. Mark location of holes for the mounting brackets, making
sure holes are plumb. For a person 5'8" – 6'2" tall, we recom-
mend placing the holes of the upper bracket at 72
5 /
8
" from
finished floor height. 3 From the upper bracket holes, measure
down 42 1 /
8
" for location of the lower bracket holes.
NOTE—Before drilling holes for the brackets, make certain the
Showerspa will rest flat against finished wall surface at the
desired mounting height with the supply lines connected.
5. Drill ¼" holes through wall surface using a masonry bit. Drill
slowly through wall surface to avoid cracking and chipping.
Insert anchors and securely screw brackets to wall. Before
connecting hot and cold supply lines, hang ShowerSpa on
wall, check the height and make sure ShowerSpa is flush
against wall with a secure fit.
6. Connect hot and cold water supply lines to stub-outs—
DO NOT OVERTIGHTEN. Before mounting the ShowerSpa,
check fittings to make sure they are secure. Turn on water
and check for leaks. When fittings are leak-free, mount
ShowerSpa on wall.
7. OPTIONAL—Seal around body of ShowerSpa with a bead of
silicone. DO NOT SEAL BOTTOM.
1 Additional fittings or longer supply lines may be necessary depending on your specific situation.
2 The desired mounting height of ShowerSpa determines height of the ½" stub-outs. The stub-outs must be located at a height
allowing supply lines to be connected and body of ShowerSpa to rest flat against finished wall.
3 The mounting height may vary depending on several factors (i.e. location of supply lines, interference from ShowerSpa plumbing, personal
preference, etc.)
Parts Legend
1. ShowerSpa
2. Shower Head
3. Shower Arm
4. Escutcheon
5. Shower Arm Outlet
6. Shower Arm Outlet Hose
7. Handheld Shower
8. Handheld Holder
9. Handheld Hose
10. Handheld Outlet
11. Handheld Outlet Hose
12. Large Rubber Washer ... (2)
13. Brass Nut ........................ (2)
14. Mounting Screw ............ (4)
15. Nylon Anchor ................. (4)
16. Mount Bracket ............... (2)
17. Rubber Washer .............. (6)
(1 extra)