Soul Electronics Run Free Pro - Manual

WIRELESS Active Earphones With Bluetooth
User GUIDE
RUN FREE PRO
ENGLISH
SPECIFICATIONS
Bluetooth Version:
V4.0 + EDR with Apt-X decoder support
Profile:
A2DP, AVRCP, HSP, and HFP.
Codec:
mSBC
Range:
10 meters (33 feet)
Charging time (Full charge) :
Approx. 2 hours
Working time:
up to 8 hours (Varies by volume and content)
Standby time:
up to 10 days
Dimensions:
18H x 18W x 32D (mm) earphone size, 575mm cord length
Weight:
17g
PAIRING
TIP: The cable will be longer in this wearing option. You can use the clip to
shorten the cable so it won’t interfere your training.
BATTERY
LIFE AND
CHARGING
1.
Charging the battery prior to first
use is recommended but not required.
The RUN FREE PRO is pre-charged
however initial charge will vary.
2.
Battery life status will be indicated at the
top right corner of your iPhone screen.
3.
Low battery indicator on earphones is shown
by a Red LED light. Charge the earphone when the
flashing light turns Red.
4.
When charging, Red LED light means the earphones
are being charged. A Blue LED light means the earphones
are fully charged.
WATER/
SWEAT
PROOF
1.
The earphone unit is not
completely waterproof where the
sound is output. Sound may become
muffled if water gets inside.
2.
When this happens, hold the earphones
as shown and pat 10-20 times to remove the
water. Place a dry cloth underneath the
earphones for 2-3 hours.
Please ensure the USB battery door is completely
closed and locked securely before cleaning.
NOTE: Water/sweat resistance performance of your earphones is
based on measurements stated in this manual. Malfunctions as a
result by misuse by the customer are not covered by the warranty.
AUTO
PAIRING
MODE
REMOTE
MIC
CONTROLS
1.
Paired devices will remember each other
unless pairing information is deleted.
2.
After initial pairing, simply press the center
button for 3 seconds and the earphones will be
paired with the phone/music device automatically.
3.
To pair a new phone/music device, go into Bluetooth
settings on your phone/music device, delete paired device
and repeat the “PAIRING” instructions above.
MULTIPOINT
(PAIRING WITH MORE
THAN ONE DEVICE)
1.
With SOUL multipoint technology,
you can pair and connect up to two
Bluetooth devices to your earphones.
2.
The headset must be in standby mode
(Not connected with any device or phone)
3.
To turn on, user can press the volume “+” and
“Multifunction” buttons together. User will hear a
tone which indicates the activation of this feature.
4.
To turn off, user can press the volume “-” and
“Multifunction” buttons together. User will hear a tone
which indicates the deactivation of this feature.
Blue / Red
LED light
1.
In the “OFF” position. Turn “ON” pairing mode by pressing and holding
the center button on the remote for 5 seconds until the Blue/Red LED light
starts to flash on the earphones.
2.
On your phone/music devices, turn Bluetooth on.
It should start searching for devices.
3.
Find “SOUL RUN FREE PRO” and select
(You may need to enter passcode 0000 if prompted)
4.
Voice prompt or beeping sound will indicate that the
RUN FREE PRO is connected.
5.
If pairing fails, turn off the earphones by pressing on the center
button for 5 seconds then repeat the process.
(You may also see your phone/music devices instructions for more information)
VOLUME
UP
( > 2sec )
FORWAED
TRACK
VOLUME
DOWN
( 2sec )
BACKWARD
TRACK
MIC
ON / OFF PLAY/
PAUSE
END
CALL
ANSWER
CALL
LAST
CALL
REDIAL
REFUSE
CALL
( double click )
( 2sec )
( 3sec / 5sec )
STEP 1
STEP 2
01 02
SR06-UG-EN-2
MULTIPOINT
OFF
MULTIPOINT
ON
TIP:
* Once Multipoint is on, please be sure to repeat
“PAIRING” instructions for both phones/devices.
**Please make sure the multipoint function is off
when not connected to 2 phones/devices.