SunBriteTV SB-DP46XA - Manual (Page 4)

5
Install Non-Articulating Wall Mount SB-WM46NA to Deck/Planter Pole
(If you are Installing the Articulating Mount SB-WM46, go back to Step 4.)
Horizontal
Mounting Bar
Hole Positions
Attach Horizontal Mounting Bar to Pole
There are 8 Horizontal Mounting Bar Holes at the top of the Deck Planter
Pole. Note that the Holes have been assigned Position numbers and letters.
Position Row 1 and 3 are the rows that are to be used with the Non-
Articulating Wall Mount SB-WM46NA. If you prefer a 5-inch lower viewing
angle, you can use Position Rows 2 and 4. The sample we are using for this
instruction is Position Row 1 and 3 (Figure 11) .
1. Align the top Horizontal Mounting Bar so that the fourth hole from the
outside of the bar on the left side and right side line up to Position 1a and
1b. This step will center the bar to the pole.
2. Place the 3/8” Washer over the Mounting Bar Hole at Position 1a, and put
the 1” Bolt through the Washer and Mounting Bar, to secure the Washer in
place Figure 12). From the back side attach the 3/8” Lock Nut and secure
tightly (Figure 13). Repeat steps at Position 1b, to complete installation of
the top Mounting Bar.
3. Align the lower Horizontal Mounting Bar so that the fourth hole from the
outside of the bar on the left side and right side line up to Position 3a and 3b.
This step will center the bar to the pole.
4. Place the 3/8” Washer over the Mounting Bar Hole at Position 3a, and put
the 1” Bolt through the Washer and Mounting Bar, to secure the Washer in
place. From the back side attach the 3/8” Lock Nut and secure tightly. Repeat
steps at Position 3b, to complete installation of the bottom Mounting Bar.
1a 1b
3a 3b
Deck Planter Pole
1a
2a
3a
4a
1b
2b
3b
4b
Horizontal
Mounting Bars
Attach Non-Articulating Wall Mount SB-WM46NA to
Deck/Planter Pole
1. Install all four Unistrut Nuts on the Horizontal
Mounting Bar:
A. Align the channel of the Unistrut Nut with the
Mounting Bar Lip (Figure 14).
B. Slide the Unistrut Nuts in 2.25” from each end of
Mounting Bar. The Unistrut Nuts will be 16 inches
apart, and in position to accept the Wall Mount
(Figure 15).
2. Attach Non-Articulating Wall Bracket (sold separately) to
the Horizontal Mounting Bar
A. Align the Non Articulating wall bracket to the
four Unistrut Nuts that are attached to the
Horizontal Mounting Bar.
B. Hold the 5/16” Washer in front of the Horizontal
Mounting Bar and the Unistrut Nut. Guide the
1-1/2” Bolts through the 5/16” Washers, Mounting
Bar and Unistrut Nut, and secure tightly (Figure 16).
Repeat Step B to attach the Bolt and Washer to the other
three Unistrut Nuts (Figure 17).
To complete installation, go to Step 6 on Page 5.
Figure 14
Figure 16
Unistrut Nut Placement
Mounting Bar
1-1/2” Bolt
5/16” Washer
Unistrut Nut
Unistrut Channel
Pole Plate Lip
Figure 15
1” Bolts
3/8” Washers
3/8” Lock Nuts
Figure 11
Figure 12 Figure 13
Mounting Bar
1-1/2” Bolt
Unistrut Nut
Front
Back
Figure 17