Clarion DXZ435 - Manual (Page 10)

14
DXZ435
English
Radio Operations
FM reception
For enhanced FM performance the ®
tuner includes signal actuated stereo control,
Enhanced Multi AGC, Impulse noise reduction
curcuits and Multipath noise reduction circuits.
Changing the reception area
This unit is initially set to USA frequency intervals
of 10kHz for AM and 200kHz for FM. When using it
outside the USA, the frequency reception range
can be switched to the intervals below.
●Setting the reception area
1. Press the [BND] button and select the
desired radio band (FM or AM).
2. While pressing the [A-M] button and hold the
number “2” of the [DIRECT] buttons for 2
seconds or longer, the reception area
switches from inside the USA to outside the
USA.
3. While pressing the [A-M] button and hold the
number “1” of the [DIRECT] buttons for 2
seconds or longer, the reception area
switches from outside the USA to inside the
USA.
∗ Any station preset memories are lost when the
reception area is changed.
Listening to the radio
1. Press the [FNC] button and select the radio
mode. The frequency or PS appears in the
display.
∗ PS: Programme service name
2. Press the [BND] button and select the radio
band. Each time the button is pressed, the
radio reception band changes in the following
order:
FM1
➜ FM2 ➜ FM3 ➜ AM ➜ FM1...
3. Press the [ a] or [d] button to tune in the
desired station.
Tuning
There are 3 types of tuning mode available, seek
tuning, manual tuning and preset tuning.
Seek tuning
1. Press the [BND] button and select the
desired band (FM or AM).
∗ If “MANU” is lit in the display, press and hold
the [BND] button for 1 second or longer.
“MANU” in the display goes off and seek
tuning is now available.
Basic Operations
Adjusting the Z-Enhancer Plus
1. Press the [Z+] button and select the Z-
Enhancer Plus mode to adjust.
2. Press the [A-M] button and turning the
[ROTARY] knob clockwise adjusts in the +
direction; turning it counterclockwise adjusts
in the – direction.
●When “B-BST 0” is selected, you can ad-
just the bass in the range of –3 to 3.
●When “IMPACT 0” is selected, you can
adjust the bass and treble in the range of
–3 to 3.
●When “EXCITE 0” is selected, you can ad-
just the bass and treble in the range of –3
to 3.
∗ Press and hold the [Z+] button for 2 seconds
or longer to change to the “CUSTOM” mode.
Bass/treble characteristics become flat and
the indication “Z+FLAT” is shown in the
display.
Press the [Z+] button again to change to the
“Z+ OFF” mode.
Adjusting MAGNA BASS EXTEND
The MAGNA BASS EXTEND does not adjust
the low sound area like the normal sound
adjustment function, but emphasizes the deep
bass sound area to provide you with a dynamic
sound.
∗ The factory default setting is off.
1. Press and hold the [A-M] button for 1
second or longer to turn on the MAGNA
BASS EXTEND effect. “M-B EX” lights in
the display.
2. Press and hold the [A-M] button for 1 second
or longer to turn off the MAGNA BASS
EXTEND effect. “M-B EX” goes off from the
display.
Adjusting the subwoofer
When you default select one of mode (LPF50,
LPF80, LPF120).
∗ The factory default setting is “S-VOL 0”.
(Adjustment range: –6 to +6)
1. Press the [SW-VOL ] button to select the
subwoofer volume increases or decreases.
2. Press and hold the [SW-VOL ] button, the
subwoofer volume automatically increases or
decreases.