Top Flite TOPA0950 - Manual (Page 4)

other written documentation of color must be provided.
Contact the AMA for a rule book with full details.
If you would like photos of the full-size P-51D Mustang
for scale documentation, or if you would like to study
the photos to add more scale details, photo packs are
available from:
Bob’s Aircraft Documentation
3114 Yukon Ave
Costa Mesa, CA 92626
Telephone: (714) 979-8058
Fax: (714) 979-7279
E-mail: www.bobsairdoc.com
ADDITIONAL ITEMS REQUIRED
HARDWARE & ACCESSORIES
In addition to the items listed in the “Decisions You
Must Make” section, following is the list of hardware
and accessories required to fi nish the P-51 Mustang
ARF. Order numbers are provided in parentheses.
❏
R/C foam rubber (1/4" [6mm] - HCAQ1000,
or 1/2" [13mm] - HCAQ1050)
❏
3' [900mm] Standard silicone fuel
tubing (GPMQ4131)
ADHESIVES & BUILDING SUPPLIES
In addition to common household tools (screwdrivers,
drill, etc.), this is the “short list” of the most important
items required to build the P-51 Mustang ARF. We
recommend Great Planes Pro
™ CA and Epoxy glue.
❏
1/2 oz. [15g] Thin Pro CA (GPMR6001)
❏
Pro 30-minute epoxy (GPMR6047)
❏
Pro Threadlocker (GPMR6060)
❏
Drill bits: 1/16" [1.6mm], 5/64" [2mm], 3/32" [2.4mm],
3/16" [4.8mm]
❏
8-32 Tap and drill set (GPMR8103)
❏
Silver solder w/fl ux (STAR2000)
❏
#1 Hobby knife (HCAR0105)
❏
#11 Blades (5-pack, HCAR0211)
❏
Medium T-pins (100, HCAR5150)
❏
Masking tape (TOPR8018)
❏
Denatured alcohol (for epoxy clean up)
❏
Panel Line Pen (TOPQ2510)
❏
220-grit Sandpaper
❏
Petroleum jelly or oil
OPTIONAL SUPPLIES & TOOLS
Here is a list of optional tools that will help you build
the P-51 Mustang ARF.
❏
Top Flite MonoKote ® sealing iron (TOPR2100)
❏
Top Flite Hot Sock ™ iron cover (TOPR2175)
❏
Top Flite Trim Seal Tool (TOPR2200)
❏
1/2 oz. [15g] Medium Pro CA+ (GPMR6007)
❏
1/2 oz. [15g] Thick Pro CA- (GPMR6013)
❏
Pro 6-minute epoxy (GPMR6045)
❏
Small metal fi le
❏
Stick-on segmented lead weights (GPMQ4485)
❏
2 oz. [57g] Spray CA activator (GPMR6035)
❏
4 oz. [113g] Aerosol CA activator (GPMR6034)
❏
CA applicator tips (HCAR3780)
❏
CA debonder (GPMR6039)
❏
Epoxy brushes 6, (GPMR8060)
❏
Mixing sticks (GPMR8055)
❏
Mixing cups (GPMR8056)
❏
Pliers with wire cutter (HCAR0630)
❏
Compressed air 10 oz (TAEC1060)
❏
Microballoons (TOPR1090)
❏
Switch & Charge Jack Mounting Set (GPMM1000)
❏
Ernst charge receptacle Futaba J (ERNM3001)
❏
Rotary tool such as Dremel ®
❏
Rotary tool reinforced cut-off wheel (GPMR8020)
❏
Servo horn drill (HCAR0698)
❏
Hobby Heat ™ micro torch (HCAR0750)
❏
Dead Center ™ engine mount hole
locator (GPMR8130)
❏
AccuThrow ™ Defl ection Gauge (GPMR2405)
❏
C.G. Machine ™ (GPMR2400)
❏
Precision magnetic prop balancer (TOPQ5700)
❏
Hobbico fl exible 18" ruler stainless
steel (HCAR0460)
❏
Hobbico pin vise 1/16" collet w/6 bits (HCAR0696)
❏
Hobbico 8-piece ball tip hex wrench
(SAE HCAR0520)
❏
Hobbico 7-piece ball tip hex wrench
(metric HCAR0521)
❏
Great Planes precision prop reamer
(SAE GPMQ5006)
❏
Great Planes Precision Prop Reamer
(metric GPMQ5007)
❏
Great Planes clevis installation tool (GPMR8030)
❏
X-Acto ® X-tra Hands double clip (XACR4214)
IMPORTANT BUILDING NOTES
• There are two types of screws used in this kit:
Sheet Metal Screws are designated by a number
and a length. For example #6 x 3/4" [19mm].
This is a number six screw that is 3/4" [19mm] long.
Machine Screws are designated by a number,
threads per inch, and a length. For example 4-40 x
3/4" [19mm].
This is a number four screw that is 3/4" [19mm] long
with forty threads per inch.
• When you see the term test fi t in the instructions,
it means that you should fi rst position the part on
the assembly without using any glue, then slightly
modify or custom fi t the part as necessary for the
best fi t.
• Whenever the term glue is written you should rely
upon your experience to decide what type of glue to use.
4