Winco MDS50 - Manual (Page 4)

Page 2
SPECIFICATIONS
GENERATOR SPECIFICATIONS
MDS50
KILOWATT 40 kW
KILOVOLT-AMPS (.8 PF)50.0 KVA
AMPERAGE
277/480 VOLT 3 PHASE 60.2 AMPS*
120/240 VOLT 3 PHASE 120.4 AMPS*
120/208 VOLT 3 PHASE 139 AMPS*
120/240 VOLT 1 PHASE 166.7 AMPS
*Based on .8 power factor at 130 degrees C.
Derate 3% per 1000 feet (305 meters) between 300 feet
(90 meters) and 7,500 feet (2,286 meters) above sea
level. Contact the factory for rating data for operation in
altitudes above 7,500 feet (2,286 meters).
GENERATOR RESISTANCE’S
MDS50
Main Stator .075 ohms
Main Rotor 3.6 ohms
Exciter Stator 25 ohms
Exciter Rotor .035 ohms
Exciter Voltage (F1-F2)
No Load 9.5 VDC
Full Load 39 VDC
Exciter Amperage (F1-F2)
No Load .4 Amps
Full Load 1.3 Amps
ENGINE SPECIFICATIONS
See John Deere Operation and Maintenance Manual for
complete engine specifications.
TRAILER/HOUSING
MDS50
Capacity 5000 lb.
Fuel Capacity 80 gals
Axles Single
Hitch Height Adjustable
Tires P225/75-15
Tire Pressure 35 psi
Sound Attenuated ULTRA QUIET
Housing Housing Standard
PREPARATION
NOTE: This booklet covers the entire unit, EXCEPT THE
ENGINE. See the engine manufacturer’s operator
manual for specific maintenance and care information
regarding the engine. Read ALL instructions in the
manuals provided before attempting to operate the
generator set.
UNPACKING
When receiving the unit, be sure to inspect it carefully for
freight loss or damage. Check the nameplate to be sure it
is what you ordered (proper kW, voltage, fuel, etc.). If
you have questions, contact your local authorized dealer.
If you see evidence of loss or damage at the time of
delivery, have the driver sign and describe the loss or
damage in the “memo of loss or damage” section on the
freight bill. Then contact the carrier to get instructions on
filing a claim.
When loss or damage is discovered after the equipment
is delivered, but not seen at the time of delivery, it is
referred to as “concealed damage.” Separate any dam-
aged material and contact the carrier for proper proce-
dures to file a “concealed damage” claim.
OIL REQUIREMENTS
This engine was filled at the factory with John Deere
Engine Break-In Oil. This break-in oil should be drained
and the oil filter changed after the first 100 hours of
operation.
During the break-in period, add John Deere Engine
Break-In Oil as needed to maintain the specified oil level.
A second 100-hour service interval with John Deere
Engine Break-In Oil may be required if the engine is
operated under light loads during the first 100 hours.
After the break-in period, use John Deere Torq-Grad
Supreme Plus-50 or other heavy -duty diesel engine oil
as recommended in the John Deere Engine manual. See
your engine operator's manual for recommended oil
grades and types under different operating temperatures.
OIL QUANTITY US Qt. Liters
MDS50 9.0 8.5
FUEL REQUIREMENTS
See your engine operator's manual for complete type and
grade fuel information.
Filling the Fuel Tank
Standard Trailer - The standard trailer is equipped with a
single 80 gallon fuel tank. Use caution when filling the
tank not to overflow the tank into the trailer.
WARNING PERSONAL DANGER
Never refuel a running engine,. Always stop the engine
and allow to cool before refueling.
Never allow the fuel tank to run completely empty, as air
may enter the fuel system making it necessary to bleed
the engine when restarting.