Cable/cable box tv, Direct cable connection, Cable box with rf inputs and outputs connection – Philips 32PT830H User Manual
Page 2: Cable box with audioa^ideo outputs connection, Antenna tv, Antenna connection, Ooking, Elevision
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
H
ooking
U
p
the
T
elevision
C
able
/C
able
B
ox
TV
T/fjMr Cable TV input into your home may be a single (75 ohm)
J. cable or use a cable box decoder. In either case the connec-
ion is very simple. Follow the steps below to connect your cable
signal to your new television.
Direct Cable Connections:
This connection will supply Stereo sound to the TV.
I
Connect the open end of the round Cable Company sup
plied cable to the 75Q input on the TV. Screw it down finger
tight.
Direct Cable Connection:
Cable signal
coming from
Cable Company
(Round 75 Q
coaxial cable)
Jack Panel Back of TV
Cable Box (w/RF In/Outputs):
This connection will NOT supply Stereo sound to the TV, The sound
rom the cable box will be mono.
I
Coimect the open end of the round Cable Company sup
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
Using a separate round coaxial cable, coruiect one end to the
OUT(put) (TO TV) plug on the back of the Cable Box.
Connect the other end of the round coaxial cable to the
750 input on the back of the television. Screw it down finger
tight.
NOTE: Be sure to set the OUTPUT CHANNEL SWITCH on the
back of the cable box to CH 3 or 4, then tune the cable box on the
TV to the corresponding channel, Once tuned, change channels at
he cable box, not the television.
Cable Box with RF Inputs and Outputs Connection:
Output Chaniid Switch
Cable Signal
IN from the
Cable
Company
Jack Panel Back
of Cable Box
Round 75B
Coaxial Cable
Jack Panel Back of TV
Cable Box (w/AudioA^ideo Outputs):
This connection will supply Stereo sound to the TV.
I
Connect the open end of the round Cable Company sup
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
2
Using a RCA type Video Cable, coimect one end of the
cable to the Video (or ANT, your cable box may be labeled
differenlly) Out jack on the cable box and the other end to the
AVI Video Input on the TV.
Using a RCA type Audio Left and Right Cable, connect one
end to the left and right Audio Out L & R Jacks on the
cable box. Connect the other end to the AV1 Audio L & R
Input jacks on the TV.
NOTE: Use the AV button on the TV remote control to tune to the
AVI channel for the cable box signal. Once tuned, change channels at
he cable box, not the television. Pressing the AV button repeatedly
will scroll all the AV Input channels, including the presently tuned
channel.
Cable Box with AudioA^ideo Outputs Connection:
Cable Signal IN
from ihe Cable
Company
Jack Panel Back
of Cable Box with A/V Outputs
A
ntenna
TV
A
combination antenna receives normal broadcast chan
nels ( V H F 2-13 and UHF 14—69). Your connection is
easy because there is only one 75il (ohm) antenna plug on
the back of your TV, and that’s where the antenna goes.
I
lf your antenna has a round cable (75 ohm) on the end,
then you're ready to connect it to the TV.
If your antenna has flat, twin-lead wire (300 ohm), you
first need to attach the antenna wires to the screws on a
300- to 75-ohm adapter.
2
Push the round end of the adapter (or antenna) onto the
75fl (ohm) plug on the back of the TV. If the round end of
the antenna wire is threaded, screw it down finger tight.
3
Plug the television in to the wall outlet and turn the TV
on. Refer to the TUNER and AUTOPROGRAM features
within the Directions for Use. TUNER should be set to the
ANTENNA option. AUTOPROGRAM can be set to program
all the available channels on your antenna signal into the tele
vision’s memory.
Antenna Connection:
Outdoor or Indoor Antenna
(Combination VHF/UHF)
The condjination antenna receives normal
broadcast channels 2-13 (VHF) and 14-69 (UHF).
Jack Panel
Back of TV
AC Power
Wall Gullet
Power Plug
from back of TV
Round 7311
Coaxial Cable
from Antenna
2