Sears 944.528117 - Manual (Page 3)

6, When cleaning, repairing or inspecting the snow thrower,
stop the engine and make certain the collector/impel-
ler and all moving parts have stopped. Disconnect
the spark plug wire and keep the wire away from the
plug to prevent someone from accidentally starting the
engine,
7, Do not run the engine indoors, except when starting
the engine and for transporting the snow thrower in or
out of the building. Open the outside doors; exhaust
fumes are dangerous,
8, Exercise extreme caution when operating on slopes,
9, Never operatethe snow thrower without proper guards,
and other safety protective devices in place and work­
ing.
10, Never direct the discharge toward people or areas
where property damage can occur. Keep children and
others away,
11, Do not overload the machine capacity by attempting
to clear snow at too fast a rate,
12, Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care when
operating in reverse,
13, Disengage power to the collector/impeller when snow
thrower is transported or not in use,
14, Use only attachments and accessories approved by
the manufacturer of the snow thrower (such as wheel
weights, counterweights, or cabs),
15, Never operate the snow thrower without good visibility
or light. Always be sure ofyourfooting, and keep a firm
hold on the handles. Walk; never run,
16, Never touch a hot engine or muffler,
CONGRATULATIONS on your purchase of a new snow
thrower. It has been designed, engineered and manufac­
tured to give best possible dependability and performance.
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center. We have competent, well-trained technicians and
the proper tools to service or repair this unit.
Please read and retain this manual. The instructions will
enable you to assemble and maintain your snow thrower
properly. Always observe the “SAFETY RULES”,
SERIAL NUMBER:
DATE OF PURCHASE:
THEMODELANDSERIALNUMBERSWILLBE FOUND
ONADECALATTACHEDTOTHEREAROFTHESNOW
THROWER HOUSING.
YOU SHOULD RECORD BOTH SERIALNUMBER AND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
Clearing a Clogged Discharge Chute
Hand contact with the rotating impeller inside the discharge
chute is the most common cause of injury associated with
snow throwers. Never use your hand to clean out the dis­
charge chute. To clear the chute:
1, SHUT THE ENGINE OFF!
2, Wait 10 seconds to be sure the impeller blades have
stopped rotating.
3, Always use a clean-out tool, not your hands.
Maintenance and Storage
1, Check shear bolts and other bolts at frequent intervals
for proper tightness to be sure the equipment is in safe
working condition,
2, Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present
such as hot water heaters, space heaters, or clothes
dryers. Allow the engine to cool before storing in any
enclosure,
3, Always refer to operator’s manual for important details
if the snow thrower is to be stored for an extended
period,
4, Maintain or replace safety and instruction labels, as
necessary,
5, Run the machine a few minutes after throwing snow
to prevent freeze-up of the collector/impeller.
PRODUCT SPECIFICATIONS
Gasoline Capacity 3,0 Quarts (2,84 Liters)
and Type: Unleaded Regular only
Oil Type SAE 5W-30 or 10W-30
(API SG-SL): Synthetic SAE 5W-30
Oil Capacity: 21 Ounces (0,62 Liters)
Spark Plug: Champion QC12YC
Gap: 0.030" (0,762 mm)
CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules,
• Follow a regular schedule in maintaining, caring for
and using your snow thrower,
• Follow the instructions under “Maintenance” and “Stor­
age” sections of this owner’s manual.
TABLE OF CONTENTS
SAFETY RULES.......................................................................2-3
PRODUCT SPECIFICATIONS.................................................... 3
CUSTOMER RESPONSIBILITIES.............................................. 3
WARRANTY................................................................................ 4
ASSEMBLY / PRE-OPERATION............................................. 5-8
OPERATION...........................................................................9-14
MAINTENANCE....................................................................15-16
MAINTENANCE SCHEDULE....................................................15
SERVICE AND ADJUSTMENTS......................................... 17-19
STORAGE..................................................................................20
TROUBLESHOOTING.............................................................. 21
REPAIR PARTS................................................................... 22-43