Document Outline

• Copyright
• Table of Contents
• Feature Guide
  • How The Manual Is Organized
  • The P/I-AP55T Package
  • Main Features
  • Bundled Software
  • Static Electricity Precautions
  • Mainboard Layout
• O CD (DCDCD
  • Using Your Mainboard
    • Hardware Settings
      • Jumpers and caps
      • Jumper cap 3*pin jumper 2-pin jumper Jumper block
        • Jumper diagrams
    • The System Configuration Record
      • Important-
    • System IRQs
    • BIOS-Supported Enhanced IDE Features
      • Large IDE Hard Disks
      • Other IDE Devices
      • Dual IDE Channel Support
      • Faster Data Transfer
    • Power Conservation
    • Onboard VGA & Audio Features
      • VGA Hardware & Software
      • Audio Hardware & Software
    • SCSI BIOS Firmware & The Optional SC-200 Controller Card
  • Installing Expansion Cards
    • Installation Procedure
      • 2-1
    • Assigning System IRQs for Expansion Cards
      • Installing Expansion Cards That Use An IRQ
      • Example PCI installation procedure:
      • Example ISA installation procedure:
  • Upgrading System Memory
    • Configuring System Memory
      • Memory Combinations
    • Installing SIMMs
      • Installing a Memory Module
  • Upgrading Video DRAM Memory
  • Installing IDE Hard Disks
    • Installing a Primary IDE Hard Disk
    • Installing Additional IDE Devices
  • Updating the Flash BIOS
    • BIOS Update Procedure
  • Installing a Pentium Upgrade
  • Software Guide
    • Award BIOS Setup
      • Main Program Screen
      • Standard CMOS Setup
        • Standard CMOS Setup Screen
        • Date & Time
        • Hard Drive Type
        • Floppy Disk Drives
        • Video Display Types
        • Error Handling
      • BIOS Features Setup
        • BIOS Features Setup Screen
        • Virus Protection
        • Cache Control
        • Boot Up Features
        • IDE Modes
        • Keyboard Interface
        • Password Control
        • IDE Second Channel Control
        • Shadow Controls
      • Chipset Features Setup
        • Chipset Features Screen
        • Controller Settings
        • Serial Ports
        • Parallel Port
        • Parallel Port Mode
        • ECP DMA Select
        • UART2 Use Infrared *
      • Power Management Setup
        • THb Power Management Setup Screen
        • Power Management
    • 3-16
      • Video Off
      • Suspend Switch
      • Doze & Standby Speeds
      • PM Timers
      • PM Events
      • IRQ3 to IRQ15 Individual Settings
      • PCI and PNP Configuration Setup
        • PCI And PNP Configuration Setup Screen
        • Plug And Play
      • Load BIOS Defaults
        • Load BIOS Defaults Screen
      • Load Setup Defaults
        • Load Setup Defaults Screen
        • Setting Supervisor & User Passwords
          • Password Setting
      • IDE HDD Auto Detection
        • IDE HDD Auto Detection Screen
        • Save And Exit Setup
        • Exit Without Saving
      • NCR SCSI BIOS & Drivers
      • Flash Memory Writer Utility
        • The Flash Memory Writer Utility Screen
        • The Advanced Features Screen
  • Technical Summary
    • Jumper Setting Summary
      • Base Address Selector: JP1 & JP2
      • 220h
      • 240h
      • 260h
      • 280h
        • Bus & CPU External Clock Speed Selector: JP4, JP5 & JP6
        • 66MHz
        • 60MHz
        • SOMHz
        • PS/2 Mouse Port Selector: JP7
        • Enable PS/2 Mouse
        • Disable PS/2 Mouse
      • Flash EPROM Voltage Selector: JP8
        • +5-Volt
        • EPROM
        • +12-Volt
        • EPROM
      • Flash EPROM Read/Write Selector: JP9
        • Normal Read Write Protect
      • Level 2 Cache Size: JP10
        • 2S6KB Cache 512KB Cache
      • CPU Internal Clock External Mulitple Salector: JP11 & JP12
        • 1.5xExtClk 2.5xExtClk
        • 2xExtClk SxExtClk
      • RTC Clear CMOS Memory: JP13
        • Normal
        • Clear CMOS memory
      • Voltage Regulator Type Selector JP15
        • LP2951 Open
        • LT1084
        • LP2951
        • LT10M
      • Voltage Regulator Output Selector: JP16, JP17
        • 3.3V +5% STO/VR
        • 3.4V-3.6V
        • VRE
      • Voltage Regulator Module Selector: JP19, JP20, JP21, JP22
        • VRM Installed
        • COM 2 Mode Selector: JP24 & JP25
    • Memory Subsystem
      • Memory Specifications:
      • Memory Configurations
      • Level 2 Cache Options
      • Expansion Video DRAM Specifications;
    • External Connections
      • Connector Locations
      • Connector Block
      • [Pin 1 Corner]
      • Power LED
      • SMI Suspend Switch s
      • SMO Suspend Signal
      • Reset
      • Keylock
      • Speaker
        • Other Feature Connectors
        • Audio Connectots
      • Pin Assignments
        • External Audio Module
      • Pini
      • Pini
      • Controller Cables
      • Connecting A Power Supply
        • Connecting Power Supply Leads
      • Onboard ATI mach64 Information
    • The PCI-SC200 SCSI Interface Card
      • The PCI-SC200 SCSI Interface Card
      • Internal SCSI ribbon cable connector
      • External SCSI 2 cable connector
      • PCI edge connector
      • Setting Up the PCI-SC200
        • Setting the INT Assignment
        • JPl & 2: Interrupt settings
      • INT A
      • (default)
        • INTB
      • INTO
      • INTO
        • Terminator Settings
        • JP5: Terminator setting
        • Termination
        • Enabled
        • (default)
        • Termination
        • Disabled
          • Example 1: Only internal or only external devices connected
        • Note: SCSI controller card ID# is "7".
          • Example 2: Both internal and external devices connected
        • Note: SCSI interface card ID# is still "7^
      • SCSI ID Numbers