Black & Decker 44502-02 User Manual
Hammers, Electric, Important
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
HAMMER
TOOLS
-----
STAR DRILLS
I
F®r V
4
" to
V*
hole sizes (Taper "A" Shank). Use witn and 1" Ham
mers. Can also be used with IVii" Hammer, (requires an extra Chuck
Wrench No. 22749).
Cat
Ni.
Point
Diam.
Over
all
Lgth.
Qty.
in
box
Cat
No.
Point
Diam.
Over
all
Lgth.
Till
V4“"
5
W
6
7162
%“
9“
7168
5/16"
5“
6
9372
w
18“
7160
%“
5“
6
7171
11/16“
9"
7189
7/16“
5“
6
7163
9“
7161
9"
6
9380
18"
9364
Ml”
18“
1
9382
%“
24*
7170
9/16“
9“
6
50058
9"
50062
1
“
9“
For 11/18" to IVi" hole sizes (Taper “B"
IViz" Hammer. Can also be used with V
Chuck Wrench No. 23806).
Shank). Mainly for use with
Hammer (requires additional
Scaling
Chisels
No. 22887
2
W'xl
2
"
24873
23081
23082
23083
7172
7087
9388
§390
11/16“
13/16“
7/fe“
9“
9“
18“
24“
9“
9“
18“
24“
7173
7098
9396
9398
10751
10981
50065
50069
15/16“
1“
1
“
r
m"
IW'
1 V4 "
m“
9“
9“
18“
24“
12
“
24“
14
14“
No. 11108
%"x8"
Cold
Chisels
No.7095
7/fe"x9"
No. §405
7/fe"K20"
Flat
Wood
Chisels
No. 9039
2“x9"
For IV
4
“ to 2" hole sizes (Shank No. 2). Use with IW’
Requires additional Turning Handle No. 21726.
hammers.
21942
21943
21944
21948
IV
4
“
18“
1
21947
m”
30“
IV
4
“
30“
1
21948
1¥4“
18“
1
%“
18“
1
21950
2
“
18“
m”
18“
1
21951
2
“
30“
Bushing No. 11624
9“
Seam
No. 17232
9"
No. 9035
9“
Clay
Spade
No. 53557
4VS?"
CHUCK WRENCHES, HEAD
& TURNING HANDLE
Tool
Blanks
No. 11107
10
"
No. 7267
12
"
No. 22587 Chuck
Wraneh — shown
with
No.
17746
Dust
Shield
attached.
No. 22510 Chuck
Head
with
No.
21726
T
urnine
Handle.
Cat
No.
item
Shank
No.
Takes
Taper Use with Hammer
22587
Chuck Wrench
1
A
V
2
” & 1“
23808
Chuck Wrench
1
B
W & 1“
22749
Chuck Wrench
2
A
1
^“
22754
Chuck Wrench
2
B
m”
22510
Chuck Head
2
i
m”
21728
Turning Handle*
m”
ACCESSORIES
Each accessory and attachment
found suitable for use with
your tool is identified in this
owner’s manual.
CAUTION; The use of any other
accessory or attachment might
be Hazardous.
IMPORTANT
To assure product SAFETY and
RELIABILITY
repairs,
mainte
nance (excluding brush inspec
tion & replacement) and ad
justments should be performed
by BLACK & DECKER Service
Center or other qualified service
organizations,
always
using
BLACK & DECKER replacement
parts.
SAFETY RULES FOR POWER TOOLS
1 KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
2. AVOID DANGEROUS ENVIRONMENT. Don't expose power tools to rain. Don’t use power tool in
damp or wet locations. And keep work area well lit.
3. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.
4.
STORE
IDLE
TOOLS.
When not in use, tools should be stored in dry, high or locked*up place-
out of reach of children.
5.
DON'T FORCE TOOL.
It will do the job better and safer at the rate for which it was designed.
6. USE RIGHT TOOL. Don't force small tool or attachment to do the job of a heavy duty tool.
7.
WEAR PROPER APPAREL.
No loose clothing or jewelry to get caught in moving parts. Rubber
gloves and footwear are recommended when working outdoors.
8. USE SAFETY GLASSES with most tools. Also face or dust mask if cutting operation is dusty.
9. DON'T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep
cord from heat, oil and sharp edges.
10.
SECURE WORK.
Use clamps or a vise to hold work. It’s safer than using your hand and it
frees both hands to operate tool.
11.
DON'T OVERREACH.
Keep proper footing and balance at all times.
12. MAINTAIN TOOLS
Will
CAil. Keep tools sharp at all times, and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
13. DISCONNECT TOOLS. When not in use, before servicing; when changing accessories such as
blades, bits, cutters, etc.
14.
REMOVE
ADJUSTING KEYS
AND
WRENCHES.
Form habit of checking to see that keys and
adjusting wrenches are removed from tool before turning it on.
15.
AVOID ACCIDENTAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure
switch is off when plugging in.
16.
OUTDOOR USE EXTENSION
CORDS—
When tool is used outdoors, use only extension cords
suitable for use outdoors and so marked.
17.
DO NOT OPERATE
portable electric tools in gaseous or explosive atmospheres. Motors in
these tools normally spark, and the sparks might ignite fumes.
ADDITIONAL SAFETY RULES WHEN USING HAMMERS
1
. Wear safety goggles or other eye protection.
2. Wear ear protectors when hammering for extended periods.
3. Always lock the too! retainer before using Hammer.
4. Don’t overreach with the Hammer. Maintain a firm, balanced working stance. When
necessary, use only properly positioned, safe platforms, ladders and scaffolds, to do the
job SAFELY!
5. Hammer bits and tools get hot in operation. Wear gloves when touching them.
THE BLACK & DECKER MFC. CO., TOWSON, MD. 21204, U.SA.
WWW/
t
!',
electric
HAMMERS
Fornì No. 4 4 5 0 2
-
0
?
/«rrTR77 r Pii
Printed in U.S.A.