Cypress FS782 - Manual (Page 8)

FS781/82/84
Document #: 38-07029 Rev. *F Page 8 of 12
Absolute Maximum Ratings [6]
This device contains circuitry to protect the input against
damage due to high static voltages or electric fields; however,
precautions should be taken to avoid application of any
voltage higher than the absolute maximum rated voltages to this circuit. For proper operation, V
IN
and V
OUT
should be
constrained to the range, V
SS
< (V
IN
or V
OUT
) < V
DD
. All digital
inputs are tied high or low internally. Refers to electrical speci-
fications for operating supply range.
Table 5. Absolute Maximum Ratings
Parameter Description Min. Max. Unit
V
DD
Operating Voltage 3.0 6.0 VDC
VIRvss Input, relative to V
SS
–0.3 V
DD
+ 0.3 VDC
VORvss Output, relative to V
SS
–0.3 V
DD
+ 0.3 VDC
TOP Temperature, Operating 0 +70
°C
TST Temperature, Storage –65 +150
°C
T
J
Temperature, Junction – +125
°C
Table 6. DC Electrical Characteristics V
DD
= 3.3V and 5.0V ±10%, X
IN
= 48 MHz, T
A
= 0°C to 70°C
Parameter Description Min. Typ. Max. Unit
V
IL
Input Low Voltage – 0.3 * V
DD
VDC
V
IH
Input High Voltage 0.7 * V
DD
VDC
I
IL
Input Low Current 100
µA
I
IH
Input High Current 100
µA
V
OL
Output Low Voltage I
OL
= 10 mA, V
DD
= 5V 0.4 VDC
V
OH
Output High Voltage I
OH
= 10 mA, V
DD
= 5V V
DD
– 1.0 VDC
V
OL
Output Low Voltage I
OL
= 6 mA, V
DD
= 3.3V 0.4 VDC
V
OH
Output High Voltage I
OH
= 5 mA, V
DD
= 3.3V 2.4 VDC
Rpd Resistor, Pull-down (Pin 7) 60K 125K 200K
Ω
Rpu Resistor, Pull-up (Pin 3) 60K 125K 200K
Ω
C
xin
Input Capacitance (Pin 1) 8 pF
C
xout
Output Capacitance (Pin 2) 10 pF
I
CC
5V Dynamic Supply Current (C L = No Load) 38 mA
I
CC
3.3V Dynamic Supply Current (C L = No Load) 20 mA
ISC Short Circuit Current (FSOUT) 25 mA
BW BW% Variations, 3.30V
[7]
–20 0 +20 %
BW BW% Variations, 5.00V
[7]
–30 0 +30 %
Table 7. Timing Electrical Characteristics V
DD
= 3.3V and 5.0V ±10%, T
A
= 0°C to 70°C, C
L
= 15 pF, X
IN
= 48 MHz
Parameter Description Min. Typ. Max. Unit
tTLH Output Rise Time Measured at 10%–90% @ 5 VDC 1.8 2.2 2.7 ns
tTHL Output Fall Time Measured at 10%–90% @ 5 VDC 1.5 2.0 2.5 ns
tTLH Output Rise Time Measured at 0.8V–2.0V @ 5 VDC 0.5 0.65 0.8 ns
tTHL Output Fall Time Measured at 0.8V–2.0 V @ 5 VDC 0.5 0.65 0.8 ns
tTLH Output Rise Time Measured at 10%–90% @ 3.3 VDC 2.1 2.65 3.2 ns
tTHL Output Fall Time Measured at 10%–90% @ 3.3 VDC 1.7 2.1 2.6 ns
tTLH Output Rise Time Measured at 0.8V–2.0V @ 3.3 VDC 0.7 0.95 1.2 ns
tTHL Output Fall Time Measured at 0.8V–2.0 V @ 3.3 VDC 0.6 0.85 1.1 ns
TsymF1 Output Duty Cycle 45 50 55 %
Notes:
6. Single Power Supply: The Voltage on any input or /O pin cannot exceed the power pin during power-up.
7. Percentage variations from the bandwidth % values given in Table 2 and Table 3.
[+] Feedback