Dukane DPC II Plus 9001:2000 - Manual (Page 31)

21
Dukane Manual Part No. 403–566–01
Section 3 – Unpacking and Installation
Ꮨ
Ꮨ
ƽ
DUKANE CORP
ST. CHARLES, IL 60174
MADE IN USA
S E R I A L N U M B E R
U S 1 0 0 0 0
– WARNING! –
POWERLINE MUST BE GROUNDED
AT OUTLET
REMOVE ALL POWER BEFORE
REMOVING COVER OR CONNECTING
OR DISCONNECTING CABLES.
ULTRASOUND OUTPUT
SYSTEM OUT
+
–
Power Monitor Jacks
Power Signal Output Module
Power
Signal
Output
Zero Adjust
SYSTEM IN
J1
U. S . PAT E N T 4 , 2 7 7 , 7 1 0
– WARNING–
POWER LINE MUST BE
GROUNDED AT OUTLET
LINE VOLTAGE 200–240Vac 50/60Hz
15A
M O D E L N U M B E R
2 0 0 - 2 4 0 VAC, 5 0 - 6 0 H z , 1 5 A
Earth Ground
#14 Gauge
Wire
110 VAC or
220 VAC
Grounding Lug
Grounding Lug
Ultrasound
Input
Automation
Control
Status
Output
P/N 200–1302
Coaxial Cable
RG62B/U
#14 Gauge Wire
Automation
Equipment
P/N 200–1203
P/N 200–479 Ẅ
Ẅ Ẉ ẇ Ẇ
ẅ ẅ
Ꮨ
Ꮨ
ƽ
DUKANE CORP
ST. CHARLES, IL 60174
MADE IN USA
S E R I A L N U M B E R
U S 1 0 0 0 0
– WARNING! –
POWERLINE MUST BE GROUNDED
AT OUTLET
REMOVE ALL POWER BEFORE
REMOVING COVER OR CONNECTING
OR DISCONNECTING CABLES.
ULTRASOUND
OUTPUT
SYSTEM OUT
+
–
Power Monitor Jacks
Power Signal Output Module
Power
Signal
Output
Zero Adjust
SYSTEM IN
J1
U. S . PAT E N T 4 , 2 7 7 , 7 1 0
– WARNING–
POWER LINE MUST BE
GROUNDED AT OUTLET
LINE VOLTAGE
200–240Vac 50/60Hz
15A
M O D E L N U M B E R
2 0 0 - 2 4 0 VAC, 5 0 - 6 0 H z , 1 5 A
J901 T
O THR
USTER
J902 B
ASE/
ABOR
T
Jumper Block
Part No. 200–1293
Pins 3 & 9
Connected
1 5 3
6 9
Earth Ground
#14 Gauge
Wire
Flexible + Coaxial Cable
20kHz Part No. 200–624
40kHz Part No. 200–759
(Included with probe)
Grounding Lug
110 VAC or
220 VAC
14–Pin AMP to
HD–15 Adapter
Part No. 200–1248
Ẅ Ẉ
ẉ
ẇ
Ẇ
ẅ
The 3–prong AC Line cords supplied are
matched to the DPC II Plus power rating and
the continent of specified use.
The part numbers are —
200–1109
North America 110V
200–1110 North America 220V
200–1111 Continental Europe
Figure 3-4 DPC II Plus and EZ Welder Hand Probe Cable Connections
Figure 3-5 DPC II Plus and EZ Welder Automated Probe Cable Connections
Table 3— II DPC II Plus AC Power Cord Part Numbers
Step 4. Optional – Attach the status output
cable from the user–supplied
automation equipment to the System
Output DB-25 connector. Not all
automation systems will have this cable.
Step 5. Attach the power cord to the DPC II
Plus and plug the other end into an
approved AC outlet.