Operating fireplace, Continued, Optional hand-held remote operation – Desa T32N User Manual

Page 26: On/off series (models ghrcb and cghrcb), Thermostat series (models ghrctb and cghrctb), Manual mode, Auto (thermostatic) mode

Advertising
background image

111986-01A

For more information, visit www.desatech.com

For more information, visit www.desatech.com

26

OPERATING FIREPLACE

Continued

OPTIONAL HAND-HELD

REMOTE OPERATION

OPERATING FIREPLACE

Optional Hand-Held Remote Operation

Figure 52 - Setting the Selector Switch, Gas Control Knob, and
Variable Control Knob for Remote Operation

NOTICE: You must light the pilot before using the
hand-held remote control unit. See

Lighting Instruc-

tions, page 25.

1.

After lighting, let pilot flame burn for about one minute.
Turn control knob to ON position. Adjust flame adjustment
knob anywhere between HI and LO. Slide the selector switch
to the REMOTE position (see Figure 52).

Note:

The burner

may light if hand-held remote was on when selector switch
was last turned off. You can now turn the burner on and off
with the hand-held remote control unit.

IMPORTANT:

Do not leave the selector switch in the RE-

MOTE or ON position when the pilot is not lit. This will
drain the battery.

ON/OFF SERIES
(MODELS GHRCB AND CGHRCB)

Hold the control button on the hand-held remote until burner
turns on. Hold the control button again until burner turns off
(see Figure 53).

TO LOCK

press both buttons on hand-held remote control until

light stops flashing. Hand-held remote control is now locked. If
the fire is on it will be turned off automatically. In the locked
state, the light will not light up when any button is pressed.

TO UNLOCK

press both buttons together on hand-held remote

control until the light stops flashing. The hand-held remote is
now unlocked.

THERMOSTAT SERIES
(MODELS GHRCTB AND CGHRCTB)

The hand-held remote can be operated using either the manual
mode (MANU) or thermostatic mode (AUTO) (see Figure 54). To
select Fahrenheit/Centigrade mode display, carefully press the ˚C/
˚F mode button with the end of a paper clip or similar blunt object.

Manual Mode

1.

Press the POWER and LOCK buttons together to turn on
the hand-held remote control.

2.

Press the MANU button to turn on the fireplace.

3.

Press the POWER and LOCK buttons together to turn off
the fireplace.

Auto (Thermostatic) Mode

1.

Press the POWER and LOCK buttons together to turn on
the hand-held remote control.

2.

Press AUTO button to select this mode.

3.

Set the desired room temperature by pressing the TEMP
+ or - buttons.

4.

Press the POWER and LOCK buttons together to turn off
the fireplace

Note:

All remote control accessories must be purchased sepa-

rately (see Accessories, page 37). Follow instructions included
with the remote control.

O

FF

PIL

OT

O

N

L

O

IH

ON

OFF

REMO

T

E

ON

OFF

Blower Control Knob
(Optional Accessory)

Variable
Control Knob

Selector Switch in
Remote Position

Gas Control Knob
in ON Position

Figure 53 - On/Off Hand-Held Remote Control Unit (C)GHRCB

Control Button
Turns Burners
On and Off

Figure 54 - Thermostat Hand-Held Remote Control Unit
Selections (C)GHRCTB

Turns Hand-Held
Remote On or Off
and Allows You to
Choose the Manual
Setting

Selects Auto
Setting

Increases Room
Temperature in
AUTO Mode

Locks System to
Prevent Accidental
Ignition

Digital Display
Shows
Temperature and
Settings

Turns Burners
On or Off

Decreases Room
Temperature in
AUTO Mode

Advertising
This manual is related to the following products: