Elenco AC/DC Power Supply - Manual (Page 2)

INTRODUCTION
The XP-625 contains three non-filtered, non-regulated voltages:
0-30VDC @ 5A, 0-40VAC @ 5A, and 0-110VAC @ 2.5A.
All three supplies are controlled by the voltage adjust knob on the front
panel. The unit contains a volt and amp meter. The volt meter is used for
both 30VDC and 40VAC output voltages. The amp meter only registers
the DC output current. The outputs are fuse protected from overload or
shorting.
SAFETY PRECAUTIONS
CAUTION: When removing the cover, always disconnect the power cord
from the AC socket. Service repair should be done by qualified personnel
who are knowledgeable of electrical hazards.
Certain safety precautions must be observed when this power supply is
used with external circuits that are connected to AC power lines. There
is always some danger when working with electrical equipment or circuits
that operate at hazardous voltages. You should thoroughly familiarize
yourself with the equipment before working on it. High voltages may
appear at unexpected points in defective equipment.
The XP-625 is equipped with a three-wire line cord which grounds the
chassis to the power line ground. DO NOT CUT OFF OR DISABLE THE
GROUND PLUG.
SPECIFICATIONS
OPERATING INSTRUCTIONS
The power supply meters display the average voltage and current values.
The peak voltage and current values may be higher than displayed.
Connect the power supply as follows:
1. Check the voltage rating of the equipment to be powered. Care
must be taken not the exceed this rating.
2. Turn the power supply OFF.
3. Plug the line cord into a 120V, 60Hz AC outlet.
4. With the power supply turned OFF, connect the load to the
desired voltage output.
A. 0-30VDC Supply - Connect the positive lead of your
equipment to the red terminal on the front panel and the
negative lead to the black terminal.
B. 0-40VAC Supply - Connect your equipment leads to the
yellow terminals on the front panel.
C. 0-110VAC Supply - Plug your equipment into the three-
wire power outlet located on the back panel.
The 110V supply is connected to the AC input and grounded to
the chassis. The 0-40VAC and 0-30VDC are isolated from the AC
input by the power transformer. Since the 0-30VDC and 0-40VAC
supplies use the same power transformer, they must not be
connected to each other. WARNING - ANY SHORT BETWEEN
EITHER TERMINAL OF THE 0-30VDC SUPPLY AND EITHER
TERMINAL OF THE 0-40VAC SUPPLY MAY RESULT IN
DAMAGE TO THE POWER SUPPLY. If properly isolated, the
different outputs may be used at the same time. Maximum power
of all power supplies is protected by the 4A fuse.
5. Turn the power switch to the ON position. The power indicator
(red LED) on the front panel will automatically light.
6. Turn the voltage adjust knob clockwise to set the desired voltage.
7. When you are finished using the power supply, turn the voltage
adjust knob to zero (fully counter-clockwise) and turn the power
OFF (the power indicator will automatically turn off).
8. If the unit is overloaded and does not operate, turn the power
supply off, remove the line cord from the 120VAC, 60Hz outlet
and check the 4A fuse located on the back panel. If needed,
replace the fuse with another of the same rating (4A fast blow,
5 x 20mm Buss GMA-4, Elenco
® # 531044, or equivalent).
Input
Input Voltage 120VAC, 60Hz
Current Protection 4A fuse
Output
30VDC
Output Voltage 0-30VDC
Output Current 5A max.
40VAC
Output Voltage 0-40VAC
Output Current 5A max.
110VAC
Output Current 2.5A max.
Output Voltage 0-110VAC
TWO YEAR WARRANTY
All Elenco ® models are guaranteed for two full years on all parts and service. For the
first 3 months, your power supply is covered at absolutely no charge. For the remaining
21 months, a nominal service charge is required to cover shipping and handling.
When returning merchandise for repair, please include proof of purchase, a
brief letter of explanation of problem, and sufficient packing material.
Before returning any merchandise please call our service department at
(847) 541-3800 to obtain a return authorization number (RMA).