EmberGlo ES10 - Manual (Page 2)

Installation
Operation
ES10 Steamers feature a 4" deep full size steam table pan. The steamer lid is equipped with two
counter-balanced spring hinges and offers a convenient choice of four locations for installing the
lid handle at the side or front of either front corner. Models Available for either manual or fully
automatic steaming.
____________________________________
Standard ES10 Steamers are designed for use with 208 VAC to 240 VAC, 4 (3 pole with ground)
wire, single phase, 60 Hz, electrical service. (See Figure 1).
The generator casting contains two heating elements, each rated for 1600 Watts. 13.3 amps, 120
Volts, 60 Hz. Models are available for use on 50 Hz. (Non USA, Export only) electrical service.
Call your distributor for more information.
Standard units are furnished with a six foot, four conductor (2 Hot/1 Neutral/1 Ground) cord. This
cord is equipped with a male twist-lock plug and matching loose female receptacle for convenient
field installation.
____________________________________
Electrical. Female twist-lock receptacle, supplied loose with the steamer, should be installed by a
qualified electrician. Refer to wiring diagrams. Figure 1.
NOTE: Female receptacle must be wired to assure that voltage to the individual heating elements
does not exceed 150 volts. (Circuits R-W and BK-W on Fig 1 and 2.) G terminal is wired to
Ground.W terminal is wired to neutral. Protect circuit with a 15 amp double pole circuit breaker.
In the United States, Wiring to the Female receptacle must conform to local codes, or in the
absence of local codes, to the National Electrical Code ANSI/NFPA No. 70-1990, or latest
edition. In Canada, Wiring to the Female receptacle must conform to local codes, or in the
absence of local codes, to Canadian Electrical Code Part 1, CSA Standard C22.1. When
choosing a location for the steamer, be sure that there is adequate space over the unit to lift lid
completely.
Water. Connect water hose assembly to water supply system. The supply end has a 1/8" female
pipe fitting and should be attached downstream of a shut-off valve. Steamer end of hose has a
quick connect fitting which snaps onto mating fitting on steamer. This hose fitting has an
automatic shut-off valve that allows steamer to be disconnected without shutting off water supply.
After connecting, turn on water and check for leaks.
No Hood Installation Required: According to the Uniform Mechanical Codes per the
International Conference of Building Officials Code, EmberGlo Steamers do not require a separate
hood for vapor produced during operation.
____________________________________
1. Push power switch to ON position (switch lights up). Allow approximately 15 minutes for
steamer to reach operating temperature.
2. MODEL ES10PB:
Push STEAM button momentarily for each shot of steam desired. Water is sprayed into the
steam generator for as long as the button is depressed. If the STEAM button is depressed
too long or too often, flooding of the steam generator will result. A one second shot of water
every 20 seconds is a good rule of thumb to avoid flooding.
3. MODEL ES10:
A.) For a single-shot steaming as with the ES10PB (above), flip the CYCLE/MANUAL switch
to the MANUAL side. Push the STEAM button for each shot of steam desired.
B.) For unattended steaming for up to 20 minutes, set the CYCLE/MANUAL switch to
CYCLE. Depress the STEAM button to activate a steaming cycle. Steaming will proceed
according to the timer settings.
ES10 Series Installation and Service
2
Specifications
HEIGHT (lid closed)
HEIGHT (lid open 90 degrees) with lid handle mounted on
front corner of lid, projecting forward.
HEIGHT (lid open 90 degrees) with lid handle mounted on
side corner of lid, projecting to the side.
WIDTH
WIDTH with lid handle projecting to left or right side
DEPTH
24.77
73.66
58.42
57.15
72.39
55.88
Dimensions
9 3/4"
29"
23"
22 1/2"
28 1/2"
22"
Inches Centimeters
Electrical