Exo Terra Day & Night LED - Manual (Page 3)

4
of attachments not recommended or sold by the appliance
manufacturer may cause an unsafe condition.
7. Do not install or store the appliance where it will be exposed to
weather or to temperatures below freezing.
8. The safety of this appliance is guaranteed only provided that the
adaptor and light unit are properly installed. Ensure sufficient air
space around the fixture.
9. If an extension cord is necessary, a cord with a proper rating
should be used. A cord rated for less amperes or watts than the
appliance rating may overheat. Care should be taken to arrange
the cord so that it will not be tripped over or pulled.
SAVe theSe INStrUCtIONS FOr FUtUre reFereNCe.
Only the faithful observation of these installation, electrical and
maintenance guidelines will ensure the safe and efficient use of
this appliance.
exo terra ® Day & Night LeD Installation instructions
RECOMMENDATION:
• This equipment is FOR INDOOR USE ONLY.
• Warning: Disconnect the plug of this light unit, and any other
electrical equipment, used for the terrarium, paludarium or
aqua-terrarium before placing your hands in the water; and/or
performing any maintenance of any kind.
• Warning: Whenever installing or removing the Exo Terra ® Day
& Night LED or any other equipment, always ensure that it is
unplugged.
• Warning: Do not place the light unit housing near filter outputs
or expose it to water spray or humidity. Do not submerge in
water.
INStALLAtION OF LIghtINg UNIt (p. 18)
Integrated into the Exo Terra ® Day & Night LED is a self-adhesive
mounting bracket that will allow you to easily attach the unit onto
the terrarium.
1. Clean the outside surface of the terrarium glass.
2. With the protective backing still intact, place the mounting
bracket on the back or the side of the terrarium to determine its
final position.
3. Mark the position with a wax pencil or other marker.
4. Remove the protective backing and carefully fit the mounting
bracket within the marked area.
5. Make sure the tape is pressed evenly against the terrarium glass
and that no air bubbles are showing.
6. Press the adhesive side firmly against the glass panel for at least
30 seconds.
7. Wait a few moments and make sure the tape is attached firmly
to the terrarium before suspending the fixture
8. Place the LED Fixture in the mounting bracket and connect the
power supply to the fixture.
9. Simply tap the Day/Night logo touch button to switch from bright
daylight to blue night light.
Maintenance
Warning:
• Disconnect the plug of this light unit, and any other electrical
equipment, used for the terrarium, paludarium or aqua-terrarium
INStrUCtIONS pertAININg tO A rISK OF FIre, eLeCtrIC
ShOCK, Or INJUrY tO perSONS
IMPORTANT SAFETY
INSTRUCTIONS
WArNINg: To guard against injury, basic safety precautions should
be observed when handling the Exo Terra ® Day & Night LED,
including the following:
1.
reAD AND FOLLOW ALL SAFetY INStrUCtIONS
and all important notices on the appliance before using. Failure
to do so may result in damage to the unit.
2. DANger – To avoid possible electrical shock, special care
should be taken. For each of the following situations, do not
attempt repairs yourself; return the appliance to an authorized
service facility for service or discard the appliance.
A. If the appliance falls into the water, DON’T reach for it! First
unplug it and then retrieve it. If the electrical components of the
appliance get wet, unplug the appliance immediately.
B. Carefully examine the appliance after installation. It should not
be plugged in if there is water on parts not intended to be wet.
C. Do not operate any appliance if it has a damaged electrical cord
or plug, or if it is malfunctioning or if it is dropped or damaged
in any manner. The power cord of this appliance cannot be
replaced: if the cord is damaged, the appliance should be
discarded. Never cut the cord.
D. To avoid the possibility of the
appliance plug or electrical
outlet getting wet, position the
appliance to one side of a wall
mounted outlet to prevent water
from dripping onto the outlet or
plug. A “drip-loop” should be
arranged. The “drip-loop” is that
part of the cord below the level
of the unit and the outlet, or the
connector if an extension cord
is used, to prevent water from
traveling along the cord and
coming in contact with the outlet or light unit. If the plug or outlet
does get wet, DON’T unplug the electrical cord. Disconnect the
fuse or circuit breaker that supplies power to the appliance, then
unplug and examine for presence of water in the outlet.
3. This appliance is not intended for use by persons (including
children) with reduced physical sensory or mental capabilities,
or lack of experience or knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
4. To avoid injury, do not contact hot parts.
5. Always unplug an appliance from an outlet when not in use,
before putting on or taking off parts, and before cleaning. Never
yank cord to pull plug from outlet. Grasp the plug and pull to
disconnect.
6. Do not use the appliance for other than intended use. The use
ENGLISH
FRANÇAIS
ESP
AÑOL