GoDEX GS220 User Manual

Gs220, Bar code scanner, Quick start guide

Advertising
background image

Getting Started

Turn off the computer’s power before connecting the scanner, then

power up the computer once the scanner is fully connected.

Connecting the Scanner

USB:

Keyboard Wedge:

Reading Techniques

Recall Defaults

The following bar code resets all standard product default settings.

Interface Selections
USB

Keyboard Wedge

³

9

9

9

9

9

8

Recall Defaults

³

3 1 6 4 0 0

USB Keyboard

Emulation

³

5 1 5 5 1 4 3

Keyboard Wedge Emulation

Prefix

Scan one of the following bar codes to program your scanner to add

or remove a start of text character, or AIM or Nixdorf identification

characters before each bar code.

³

1

1

6

6

1

5

³

1

1

6

6

0

5

³

1

0

7

9

0

5

STX Prefix On

STX Prefix Off

³

1

0

7

9

1

5

AIM ID Prefix On

AIM ID Prefix Off

Suffix

Scan one of the following bar codes to program your scanner to add

or remove a carriage return, line feed, tab, or end of text after each

bar code.

³

1

1

6

6

1

3

³

1

1

6

6

0

3

³

1

1

6

6

0

4

CR Suffix On

CR Suffix Off

³

1

1

6

6

1

2

LF Suffix On

³

1

1

6

6

0

2

LF Suffix Off

³

1

1

6

6

1

0

Tab Suffix On

³

1

1

6

6

0

0

Tab Suffix Off

³

1

1

6

6

1

4

ETX Suffix On

ETX Suffix Off

User Configurable Prefix/Suffix

One or two prefix or suffix characters can be added and assigned for

data transmission. Use one of the codes below with a 3 code byte

sequence that represents the desired character (see

ASCII

Conversion Chart

, end of document) for your prefix or suffix. (To add

additional prefix/suffix characters, refer to your Single-Line

Configuration Guide.)
Scan the

Enter/Exit Programming bar code to begin. Then scan

the 3 digit decimal equivalent of the ASCII character into the

appropriate character location with the code byte bar codes (see

Code Bytes

, end of document). To save, scan the

Enter/Exit

Programming bar code again.
Example: To add an asterisk (*) as a prefix, scan the bar codes:
1. Enter/Exit Programming

2. Configurable Prefix #1

3. Code Byte 0

4. Code Byte 4

5. Code Byte 2

6. Enter/Exit Programming

³

9

0

4

5

0

0

Configurable Suffix #1

³

9

0

4

6

0

0

Configurable Suffix #2

³

9

0

3

5

0

0

Configurable Prefix #1

³

9

0

3

6

0

0

Configurable Prefix #2

³

9

9

9

9

9

9

Enter/Exit Programming

Supplements

Scan one of the bar codes below to program your scanner for 2 or 5

digit bar code supplements.

977 (2 Digit) Supplement Required: Turn on this feature when a 2

digit supplement is required for EAN-13 codes that begin with 977.

Scan Modes

³

1

0

1

2

1

7

2 Digit Supplements

On

³

1

0

1

2

0

7

2 Digit Supplements Off

³

1

0

1

2

1

6

5 Digit Supplements

On

³

1

0

1

2

0

6

5 Digit Supplements Off

³

1

0

1

3

1

4

977 Supplements On

³

1

0

1

3

0

4

977 Supplements Off

UPC/EAN Formatting

Scan

Convert UPC-A to EAN-13 and a leading zero is transmitted

before a UPC-A bar code to convert it to EAN-13.

Scan

Transmit Lead Zero on UPC-E to transmit a zero before each

UPC-E bar code.

³ 4 1 8 3 3 4

Continuous Blinky_1

³

1

0

7

5

1

4

Convert UPC-A to

EAN-13

³

1

0

7

5

0

4

Don’t Convert UPC-A to

EAN-13

³

1

0

7

5

1

3

Transmit Lead Zero on

UPC-E

³

1

0

7

5

0

3

Don’t Transmit Lead

Zero on UPC-E

GS220

Bar Code Scanner

Quick Start Guide

220-QS Rev D

12/12

8 1 8 9 0 0

Continuous Blinky_2

1 1 8 7 0 3

Continuous Blinky_3

Recall Defaults

³

9

9

9

9

9

8

When you scan

Continuous Blinky Scan mode, the scanner beam

flashes and scans continuously. To enter the

mode, scan below codes:

1. Enter/Exit Programming 2. Continuous Blinky_1
3. Continuous Blinky_2 4. Continuous Blinky_3
5. Enter/Exit Programming

To exit from

Continuous Blinky Scan mode, scan the Recall

Defaults barcode.

Advertising
Table of contents