Hope Tech 1 LED Adventure Headlight - Manual (Page 2)

1 2 3
4 5
4 1 2 3
We only recommend using good quality high capacity rechargeable or
disposable battery cells since this light unit is a high drain device. Using
poor quality low capacity standard alkaline cells will dramatically reduce
the burn time of the light unit. The chart below shows the burn time using
the optional (recommended) Hope Ansmann 2500mAh Ni-MH cells and
are given as a guide only. Always replace all four battery cells at the same
time and do not mix battery types.
New for 2012-13: The 1 LED Adventure lamp now features a low battery
mode which controls the lamp to drop into mode 4 (flash mode) when a low
battery voltage is detected. At this point we recommend that you either
replace the batteries or make plans to finish your ride.
CAUTION: Unlike many other LED lighting systems available, this light will
shut down when the batteries are exhausted without any dimming of the
LED. Please bear this in mind when riding at night.
With the light off:
· Press 1 – Turn light on in low power mode
· Press 2 – Switch light into medium power mode
· Press 3 – Switch light into high power mode
· Press 4 – Switch light into flash mode
Continue to cycle through power modes
upon each press of the switch.
· Press and hold for 2 seconds to turn light off.
NOTE: We recommend that you utilise the full range of power modes during use
in order to get the maximum burn time out of the battery, ie. Restrict your use of
the maximum power level to a minimum and switch back down to a lower power
level when you can.
There are no serviceable parts inside the light unit. Please do not attempt to
disassemble the unit other than removing the battery holder, as this will invalidate
the warranty. If you find that there is a problem with the functioning of the light
unit please first check that the batteries are fully charged and in good condition. If
the light still fails to function please contact Hope Technology.
*Burn times stated are using the optional (recommended) Hope Ansmann
2500mAh NiMH cells and have been tested in optimum conditions and may
therefore vary from those times shown
All Hope Technology lighting systems are covered for one year from original date
of purchase against manufacturer defects in material and workmanship. Proof of
purchase is required. Product must be returned to Hope Technology to process
any warranty claim.
This warranty does not cover any damage caused through mis-use or failing to
comply by the recommendations given in this manual.
This warranty does not affect your statutory rights.
DURATION IN HOURS
RECHARGEABLE Ni-MH 2500mAh
LOW
MED
HIGH
FLASH
0 3 6 12 18 24 30 36
35.00 HRS
3.00 HRS
7.00 HRS
24.00 HRS
1LEDAD.10.2012
OPERATION OF THE LAMP UNIT
BURN TIMES
WARRANTY
MAINTENANCE
MOUNTING OPTIONS
FITTING INSTRUCTIONS
DISPOSAL
When the equipment has reached the end of its life please dispose
of the components in accordance with your local waste regulations.
Lamps and batteries should be recycled where possible and not
disposed of with regular waste. Disused batteries can be returned
to Hope Technology for recycling.
Li-Ion
1. Select the appropriate rubber plugs for your bar size and insert into location holes
in the handlebar mount.
2. Attach mount to the light unit using the supplied M5 x 10mm bolt, ensuring that
the o-ring is located in the groove in the mount.
3. Attach the mount to the handlebar as close to the stem as possible and lock in
place with the quick release lever.
4. Select an appropriate location to fit the battery case (eg. underneath or on top of
the stem).
5. Secure in position using the supplied elasticated battery case strap.
1. Attach the mount adapter to the light unit using the supplied M5 x 10mm bolt.
2. Slide the mount adapter into the head harness and align the bolt holes. Secure in
place using the supplied M5 x 20mm bolt and locknut whilst ensuring there is just
enough freedom to adjust the tilt angle during use (if required).
3. Fit the battery case to the rear of the harness by feeding the elasticated strap
through the loops on the rear of the head harness.
4. Press the power cable into the cable clip on the top strap.
1. Attach the mount adapter to the light unit using the supplied M5 x 12mm bolt.
2. Slide the helmet mount over the mount adapter and align the bolt holes.
3. Secure in place using the supplied M5 x 20mm bolt and locknut whilst ensuring
there is just enough freedom to adjust the tilt angle while riding if required.
4. Attach the lamp unit to your helmet using the hook and loop strap.
5. Attach the battery case to the rear of the helmet using the supplied elasticated
battery strap.
HELMET MOUNT
HEAD HARNESS
Head harness Helmet mount Handlebar mount
1 2
3 4 5
Std. bar dia. OS bar dia.
HANDLEBAR MOUNT