Konig Electronic Universal remote control for 2 devices - Manual (Page 3)

3
A. How to Enter Codes
1. Switch on the home appliance you wish to control and look up the first set of codes
of the home appliance in the code chart. For example: if you wish to insert the code
a PHILIPS TV set, the first set of code shall be 1492.
2. Press the “TV” button and the indicator light will light up.
3. Press and hold the “Volume+” and “Channel+” buttons at the same time until the
indicator is switched on. Then release both buttons (the indicator light will switch off
and then on again).
4. Enter the 4-digit code. For example: the first set of codes for a PHILIPS TV set is
1492. Enter 1492.
Note:
I. The code entered is correct. The indicator light will flash twice before switching
off.
II. The code entered is incorrect. The indicator light will flash three times. Please
re-enter the code.
III. To exit the setting function, press the “Select Equipment Button”. For example:
Press the TV button if the previous setting is TV.
5. After entering in the code, the indicator light will switch off.
6. Check if the other buttons operate correctly. If this is the case, the setting was
successful. If the buttons do not function correctly, please repeat steps 2 to 6 until
you have found the right code.
NOTE: If you install a satellite receiver, follow the same procedure as mentioned above
under A, but instead of pressing the “TV” button press the “SAT” button and in the code list
search for the right code for the satellite receiver.
B. How to Search for Codes Automatically
1. Switch on the home appliance you wish to control. Place the remote control directly
at the home appliance, for example your TV.
2. Press and hold the “TV” button; the indicator light will light up.
3. Press and hold the “Volume+” and “Channel+” buttons at the same time until the
indicator light lights up. Then release both buttons (the indicator light will switch off
and then on again).
4. Press and hold the “POWER” button until the TV set is switched off. Release the
“POWER” button immediately.
5. Check if the other buttons operate correctly. If this is the case, the setting was
successful. If the buttons do not function correctly, please repeat steps 2 to 5 until
you have found the right code.
NOTE: If you install a satellite receiver, please follow the same procedure as mentioned
above under B, but instead of pressing the “TV” button you should press the “SAT” button.
Setting Favourite Channel
Use this function to set your favourite channels in “Favourite Channel”.
Setting Method:
1. Press the “TV” button and select the equipment you want to set.
Press and hold the “Volume+” and “Channel+” buttons at the same time until the
indicator is switched on. Then release both buttons (the indicator light will switch off
and then on again).
Enter code 9993 manually. The indicator light lights up to indicate that the FAV setting
is in start-up mode.
2. Enter the channel number of your favourite channel. Press the “Power” button to enter
one channel number. Then enter the next channel number. Press the “TV” button after
you have entered all the favourite channels. The indicator light switches off. The
setting is completed. (The memory space is full when the indicator light flashes 5 times.
No channel number can be entered anymore).
For example: Under the TV page you wish to enter channels (02), (38) and (56) as
your favourite channels. Enter the code 9993 manually before entering the channel
number one by one.
02
POWER 38 POWER 56 TV
When the indicator light is switched off, the settings are completed.
3. In normal mode, press the “FAV” button with the remote control pointing at the TV set.
You can find your favourite channel in the order of settings. Press the “FAV” button and
your next favourite channel in the setting list will appear.
Clear Favourite Channel
Settin Method:
1. When setting the “FAV” channel, you can press the “FAV” button to clear the wrong
channel entered or re-set the settings. Press the “FAV” button once to clear an
undesired channel (one-button command). When a “Favourite Channel” is cleared, the
indicator light will flash three times.