Luxul XVW-P30 - Manual (Page 2)

Quick Install Guide
Model Number: XVW-P30/XVW-P30-E Wireless Range Extender/Bridge
FCC ID: W59XVWP30 IC: 8584A-XVWP30
© 2014 Luxul. All Rights Reserved.
No part of this publication may be modifi ed or adapted in any way, for any
purposes without permission in writing from Luxul. The material in this manual
is subject to change without notice. Luxul reserves the right to make changes
to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual
property rights. An implied license only exists for equipment, circuits and
subsystems contained in this or any Luxul product.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
DOCUMENT CONVENTIONS
The following alert is used to indicate notable situations:
NOTE: Tips, hints, or special requirements that you
should take note of.
CAUTION: Care is required. Disregarding a caution can
result in data loss or equipment malfunction.
WARNING!: Indicates a condition or procedure that
could result in personal injury or
equipment damage.
CONTACT LUXUL
Sales
P: 801-822-5450
E: [email protected]
Technical Support
P: 801-822-5450
E: [email protected]
PACKAGE CONTENTS
The following items should be included in the box:
 One: XVW-P30 or XVW-P30-E
 One: Quick Install Guide
NOTE: If any of the listed items are missing or damaged,
please contact the reseller from whom you
purchased for return/replacement.
HARDWARE DESCRIPTION
XVW-P30: U.S. Plug (Type A)
XVW-P30-E: Euro Plug (Type C)
View of the Ethernet Ports, USB Ports and LEDs. XVW-P30 shown.
LEDs
This device has two LEDs, positioned on the front lower right corner.
The LEDs are labeled: Power, Status.
LED Indicators
Indicator Name Description
Power/Green
On The power is on
Off No Power check connections
Status/Blue
Green Green The device is confi gured and
attached to a wireless network
Blue The device is not confi gured but
is broadcasting and ready for
confi guration
Flashing
Blue/
Green Repeater is not connected to the
wireless router/AP. Check password
or status of wireless router/AP
Ethernet Ports
With 2 Ethernet ports, this device provides a simple method for
creating an Ethernet Bridge Link.
Bottom Ports
USB Port and Reset
The right panel has the Reset/Factory Default Button and
USB charging port.
Right Port and Reset
USB Charging Port
The USB on the right panel is a Charge Only Port.
NOTE: Please note this should charge most USB
powered devices but is not certifi ed by any device
manufacturer. (May not support some tablets).
Reset/Factory Default Button
The Reset button is used to clear the current settings and restore
factory default settings.
To Restore the Default Settings: With the XVW-P30/XVW-P30-E
powered on, press and hold the Reset button for 6 seconds. The
Status LED turns off, after a few seconds when the reset button is
released and after a the blue LED will begin to blink. The power LED
will stay solid. The device will be reset to factory defaults.
INSTALLATION
System and Power Requirements
 Computer or wireless device supporting TCP/IP and equipped
with a Web browser. Supported Web browser versions include
the most current versions of Firefox, Safari, Chrome, and Opera.
The Web browser is used for confi guration.
 Available power outlet
Confi guration
 Plug XVW-P30/XVW-P30-E into power outlet.
 Wireless Confi guration: Connect your wireless client device
to the Wireless network SSID: Luxul-XVW-P30.
 Wired Confi guration: Connect an Ethernet cable from your
client device to an RJ-45 port on the XVW-P30/XVW-P30-E.
 Open a web browser and enter the IP address 192.168.0.11
 Select the mode you want to use: Range Extender or Bridge
 Range Extender: Extends wireless coverage of your existing
2.4GHz network and allows devices to be connected to the
XVW-P30/XVW-P30-E Ethernet ports for network access.
NOTE: Range Extender mode may reduce the wireless
data rates of your network.
 Bridge: Allows Ethernet devices to be connected to the
RJ-45 ports on the XVW-P30/XVW-P30-E without extending
the wireless network.
 You will be presented with a list of SSIDs of available Networks
to which the XVW-P30/XVW-P30-E may be connected. If you do
not see the wireless router/AP you’re looking for, press the Scan
button to refresh the list.
 You will be prompted to enter the password of the wireless
router/AP to which the XVW-P30/XVW-P30-E is connected.
 After entering the password, it will take approximately 30
seconds to fi nish the setup. Check the Status LED on the device.
 Solid green: the device has been successfully installed and
is now working.
 Flashing blue/green: there was a problem with the setup
process, (most likely the password was not entered correctly).
Reset/Factory Default the wireless range extender and repeat
setup process.
2 3 4 5 6