NEMO Equipment GOG ELITE - Manual

2
4
OVERVIEW
1. ExoFly™ Retractable Front Rain Fly
2. ExoFly™ Door Tie-backs and Guy-Out Loop
3. Swallowtail Transforming Bivy End
4. Additional Anchors
5. Removable Internal Airbeam
6. Mesh Canopy
7. ExoFly™ Interchangeable Anchor
www.nemoequipment.com
NEMO EQUIPMENT INC.
100 Factory Street, Nashua, NH 03060
Phone: 1-800-997-9301
E-mail: [email protected]
SET UP
Lay out the contents of Gogo™ and make sure you received your tent
and the following items: stuff sack (snapped into tent), Integrated
Pump, replacement bladder with inflate/deflate valve, 5 stakes, and
repair kit. Also confirm that you received any optional items you may
have ordered including: Nemoid™ foot pump, T-shirts, or accessories.
In a flat area, begin the setup of Gogo™ by staking it out. Use the ladder
lock buckle to adjust the length of the front anchor. When your anchor
is properly adjusted, you will be able to use one stake placement to
secure either the inner tent or the ExoFly™.
1
3
4
5
2
To take Gogo™ down, first remove all gear and as much moisture as
possible. Water will add weight to your pack and can lead to mildew.
1
Begin by placing the deflator cap on the inflate/deflate valve. When
properly connected, there will be an audible click. As pressure is
released, the airbeam will immediately deflate.
2
Roll the tent along its airbeam towards the valve to force out all of the
air. Try to clean as much dirt and debris from your tent as possible
before packing it. This will help preserve the breathability of the tent
fabrics and reduce overall wear and tear.
3
The stuff sack for Gogo™ doubles as a gear stash pocket inside the tent.
To use as a stuff sack, simply turn inside out and begin stuffing the tent.
(Hint: you can avoid trapping air if you start stuffing from the foot end)
4
Fold the top edge of the stuff sack down several times to make an
air-tight seal. Allow excess air to escape while compressing. Secure the
stuff sack with the compression straps around the bottom edge.
5
Remember to leave no trace. Before leaving your campsite take a
thorough look around making sure you have not left anything behind,
out of place, or damaged.
6
TAKE DOWN
Gogo™
2
1
7
6
5 4
1. Integrated Pump Body
2. Quick-Disconnect Inflator
3. Mouthpiece
4. Universal Inflation Port / Moisture Release Valve
5. Velcro Straps for Attachment Inside Tent Shell
6. Bladder Access Pocket
7. Hypalon® Valve Reinforcement
8. Velcro Panels for Securing Airbeam Ends
9. Protective Cap for Valve
10. Deflator
11. Quick-Disconnect Inflate/Deflate Valve
5
11
10
7
9
6
3
2
4
1
Integrated Pump and Airbeam
1
5 5
3 2
8
3
5
The first time you set up Gogo™, you will need to attach the airbeam.
Line up and attach the Velcro straps. Keep your airbeam attached to
save setup time in the future.
Connect the inflator end of the pump to the inflate/deflate valve on the
airbeam. When properly connected, the quick-disconnect fittings will
make an audible click.
To use the Integrated Pump, first make sure the universal inflation port
on top of the pump is closed. Blow into the pump through the mouth
piece, and squeeze the pump body with your hand or under your foot.
Repeat this sequence, being sure to frequently inhale.
*Patents Pending
3
GOGO ™
©2007 NEMO Equipment, Inc.