Peg-Perego John Deere Mini Power Loader - Manual (Page 5)

15 • Finish fastening the handlebar by holding the
nuts in place while tightening the screws.
16 • Insert the rod for the shovel command lever
into the hole in the shovel.
17 • Place a large stud in the special tool (see detail
A).
18 • Fasten the rod by pushing the stud all the way
in. (If this is difficult to do, use a hammer).
19 • Press the two loader-arm rests into place on the
sides of the grill, as shown in the figure. The two
pieces are shaped to fit the grill, so make sure
to position them carefully, inserting the pin
marked “L” on the left and the pin marked “R”
on the right.
20 • Remove the pin that fastens the loader to the
tractor from the loader arms, as shown in the
figure.
21 • Place the loader on the tractor, lining up point
A on both sides with the previously attached
rests. Press on the back of the loader arms on
both sides to fasten them at point B.
22 • Push the pin that fastens the loader to the
tractor through its hole and out the opposite
side of the tractor.
23 • Place a small stud in the special tool (see detail
A).
24 • Fasten the pin by pushing the stud all the way
in. (If this is difficult to do, use a hammer).
25 • To dump the slovel, lower the lever.
26 • To lower the entire loader, push the handlebar
forward.
This product conforms to EN 71 the
safety standard for toys.
This vehicle is not intended for use
on streets, around traffic or parked
cars.
This product meets and/or exceeds
all ASTM TOY SAFETY STANDARDS,
including F 963, Consumer Toy
Safety Specifications.
MAINTENANCE AND CARE
• Regularly check the conditions of
the vehicle. In case of fault, do not
try to use the vehicle. For repair
use only original PEG PEREGO’s
spare parts.
• PEG PEREGO assumes no liability if
the product as been tampered
with.
• Do not leave vehicle near sources
of heat such as radiators, stoves,
fireplaces, etc.
• Protect vehicle from water, rain,
snow, etc.
• Periodically lubricate (with a light
weight oil) moving parts, such as
wheel bearings, steering linkages,
and chains at points of rotation or
where they come in contact.
• The vehicle’s surface can be
cleaned with a dampcloth. Do not
use abrasive cleaners. The cleaning
must be carried out by adults only.
• Never disassemble the vehicles
mechanisms unless authorized by
PEG PEREGO.
SAFETY
WARNING!
THE CAR MUST BE USED UNDER
ADULT SUPERVISION.
• Not suitable for children under the
age of 2 years. The small pieces
could be swallowed or inhaled.
• PEG PEREGO® thanks you for choosing this
product. For over 50 years, PEG PEREGO has been
taking children for an outing: first with its famous
baby carriages and strollers, later with its pedal and
battery operated toy vehicles.
• Read this instruction manual carefully to learn the
use of the vehicle and to teach your child safe and
enjoyable driving. Please keep this manual for use
as a reference in the future.
• Our toys conform with the safety requirements
provided by the Council of the EEC, of the T.Ü.V.; of
the I.I.S.G. Istituto Italiano Sicurezza Giocattoli, and
the U.S. Consumer Toy Safety Specification F963.
Peg Perego S.p.A. is an ISO 9001
certified company.
The fact that we are certified provides
a guarantee of our honesty for our
customers, and fosters trust in the
company’s way of working.
• Peg Perego reserves the right to modify or change
its product. Price, literature, manufacturing
processes or locations or any combination of the
above mentioned entities may change at any time
for any reason without notice with impunity.
Years 2-4
Weight capacity
50 lbs
PEG PEREGO offers after-sales services, directly or
through a network of authorized service centers for
repairs or replacement parts. See the back cover of
this instruction manual for contact information.
CAUTION:
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS
COMPONENTS TO BE ASSEMBLED
MAY POSE A SMALL PARTS/SHARP
EDGE HAZARD.
ASSEMBLY
1 • Unscrew the 2 knobs under the seat.
2 • Position the seat as shown in the figure.
3 • IMPORTANT: the seat can be adjusted to 2
positions depending on the height of the child
(see figure). Position 1: the seat is higher and
further back. Position 2: the seat is lower and
further forward.
4 • Turn the vehicle on its side, keeping the seat in
position. Unscrew the chain cover under the
vehicle.
5 • Open the cover to access the seat fixing screws.
6 • Screw on the two seat fixing knobs as shown in
the figure. Close and screw on the cover.
7 • Snap on the 2 rear lights.
8 • Press on the 2 headlights as shown in detail A.
9 • Position the steering wheel. Fix the steering
wheel with the screw and washer provided.
10 • Push on the steering wheel cap as shown in the
figure.
11 • Place the handlebar on the loader arms,
slanting it downward slightly in order to
correctly position the two pins on the
handlebar (see detail in the next figure).
12 • The two pins on the handle must be kept on
the outside of the hooks that protrude from the
loader arms. The figure shows one of the two
pins in both the wrong position (NO) and the
right position (OK).
13 • Insert the tabs on the front part of the
handlebar into the openings in the loader arms.
14 • Fasten the handlebar using the screws and
nuts, inserting the nuts into the hexagonal
housings inside the loader arms, and the screws
through the circular holes from the outside.
(The figure shows the bottom of the loader
arms).
ENGLISH
CUSTOMER SERVICE
ASSEMBLY INSTRUCTIONS
VEHICLE MAINTENANCE
AND SAFETY
• Never use the vehicle on steep
slopes, near steps or stairs, in the
middle of traffic or between
parked cars.
• Children should always wear shoes
when riding in or driving a ride-
in/ride-on vehicle.
• Do not allow children to place
their hands, feet or any part of
their body, clothing or other
articles near the moving parts
while vehicle is in operation.
• Never use gasoline or other
flammable substances near the
vehicle.
• The vehicle is constructed just for
one child.