PRW 18 PRW Gold Series Flexplate (SFI-Rated 29.1) - Manual (Page 2)

shims are used, there is a good chance that the mounting surface has been machined down or it is warped. Please refer to
your local machine shop for advice on your block.
4. After adding the shim or shims, recheck the clearance in several different locations, preferably 120 degrees apart.
5. One more critical location to check is the clearance between the flexplate ring gear and starter. Normally this is not an
issue, but make sure there is a 0.100” clearance with a variance of +/- 0.040”. Again check it in several locations. If there
are clearance issues the flexplate may be warped and you should return it to your dealer. Although we check each
flexplate that we manufacture for run out, the flexplate could have been damaged during shipping.
Possible Causes for Damaged Flexplates
1. Not installing flexplate perpendicular to crankshaft flange
2. Engine or torque converter out of balance
3. Worn front pump bushing
4. Too much end play on the crank from excessive thrust bearing wear
5. Improper bolt torque and, or not in proper order according to OEM specs
6. A bad starter can wear or break off the teeth on the ring gear
7. Not properly shimming the starter, if needed, to align with the starter ring
STOP!!!! SPECIAL NOTES:
Before installing this flexplate, make certain that the application is correctly identified for your vehicle’s engine and
that the counterweight is correct for your application, the flexplate bolt pattern is correct for your make and model,
and ring gear tooth count is correct. No returns are permitted for flexplates or flywheels that have been installed!
PRW is not responsible for installation issues or mismatched parts.
CUMMINS and DODGE DIESEL FLEXPLATES
There are many variations and combinations of Cummins diesel engines and transmissions between 1989 and 2005+.
The PRW flexplate for this application is designed for high performance and racing. Do not install this flexplate if
there is less than 0.0625” clearance between the torque converter and flexplate. PRW recommends that this
application be installed by a professional mechanic or transmission specialist with specific knowledge of
Cummins engine/torque converter and transmission requirements.
LIMITATION OF WARRANTY
SELLER (PRW) hereby provides the following limited warranty as to description, quality, merchantability, fitness for any product’s purpose, productiveness, or any
other matter related to the SELLER's product sold herewith. The SELLER shall not be responsible for the product’s open use and/or service. The BUYER hereby
waives all rights other than those expressly written herein. This Warranty shall not be extended or varied except by a written agreement signed by SELLER and
BUYER.
The Warranty is Limited to manufacturers defects for a period of one (1) year from the date of sale and restricted solely to the parts contained within the product's kit.
Any products in question of Warranty require a Return Manufacturers Authorization for inspection. Product must be shipped prepaid to the SELLER and accompanied
by a dated receipt or invoice and proof of purchase. All Warranty claims are subject to approval by PRW Industries, Inc.
Under no circumstances shall the SELLER be liable for any labor, travel time, or other expenses incurred in the diagnosis of defects, removal, or reinstallation of this
product, or any other contingent expenses. Under no circumstances shall the SELLER be liable for any damage or expenses incurred by reason of the use or sale of any
such equipment. Other limitations may apply.
IN THE EVENT THAT THE BUYER DOES NOT AGREE WITH THIS POLICY: THE BUYER MAY RETURN THIS PRODUCT, IN NEW AND UNUSED CONDITION TO THE PLACE OF
PURCHASE. DATED PROOF OF PURCHASE IS REQUIRED WITHIN THIRTY (30) DAYS FROM ORIGINAL DATE OF PURCHASE TO OBTAIN A FULL REFUND. THE
INSTALLATION OF THIS PRODUCT INDICATES THAT THE BUYER HAS READ AND UNDERSTANDS THIS AGREEMENT AND ACCEPTS THE TERMS AND CONDITIONS STATED
p:\product\installation guides\ms word\18 prw sfi chromoly series flexplate 1722 v1.3.doc
PRW Industries, Inc.
1722 Illinois Avenue
Perris, California 92571
Tele: (951) 436-7900 FAX: (951) 928-8555
Tech: (888) 377-9779
www.prw-usa.com