页 11, Setting – SkyRC T6200 Charger User Manual

Page 11

Advertising
background image

T6200

T6200

19

18

PRESET

P1

P2

LiPo

6S 2.0A/1.0A

P3 LiFe 3S 2.0A/1.0A

P4 NiMH 7S 2.0A/1.0A

P5 Pb

6S 2.0A/1.0A

EDIT

EDIT

EDIT

EDIT

EDIT

HOME

LiIon 6S 2.0A/1.0A

PRESET

P1

P2

LiPo

6S 2.0A/1.0A

P3 LiFe 3S 2.0A/1.0A

P4 NiMH 7S 2.0A/1.0A

P5 Pb

6S 2.0A/1.0A

EDIT

EDIT

EDIT

EDIT

EDIT

HOME

LiIon 6S 2.0A/1.0A

CELLS

CAPACITY

BATT TYPE

Pb

Lilon

OPERATION

VOLT

METER

CHARGE

START

SETTING

LiPo

6S

C6.0A / D2.0A

PRESET

LiPo

mAh

P1

BAL CHARGE

The charger can store up to 5 different charge/discharge profiles for your convenience, and the
stored profiles can be recalled quickly without having to go through the setup process.

1. EDIT AND BACK

Touch “EDIT” to set the profiles and “HOME”

to

homepage.

Touch “CONFIRM” to confirm the setting and go back to previous screen.

EDIT

BATT TYPE CELL

Pb

OPERATION CHG CURRENT

CHARGE

DCHG CURRENT

CONFIRM

2S

0.1A

0 1A

.

Please touch “>” to change the battery
type and operation program.
Please touch “-” and “+” to get the right
battery cells count and desired charge/
discharge current.

NOTE:

2. CALL OUT

The basic settings of the profiles are displayed and you could touch the settings bar to enter
to the homepage. All the current settings will displayed in the top of the screen. please
touch and hold the desired operation program to start the progress.

MEMORY PRESET-DATA STORE/LOAD

MEMORY PRESET-DATA STORE/LOAD

You could do SYSTEM SETTING, SAFETY PROTECTION and CHARGER PARAMETER
settings when you enter to Setting program.
Please touch “ ” and “ ” to go to previous or next setting phase and touch “NEXT” to enter
to current setting program.

ITEM

KEY BEEP

BUZZER

LCD LIGHT

THEME

SELECTION

ON/OFF

ON/OFF

1-5

BLUE, RED,
YELLOW, GREEN

DESCRIPTION

The beep sounds at every time touching the screen to confirm
your action. The beep or melody sounded at various times
during operation to alert different mode changes.

The brightness of the LCD can be adjusted basing on
personal preference.

Different color theme can be selected basing on personal
preference.

1. SYSTEM SETTING

ENTER

HOME

LCD LIGHT

5

SYSTEM

SETTING

KEY BEEP

ON

ON

BUZZER

THEME

语 言
中 文

RESTORE

ENTER

NEXT

SETTING

SYSTEM
SETTING

Please touch the referred setting(selections) to change it.
When touching “RESTORE” the charger will restore factory default settings.

2. SAFETY PROTECTION

ITEM

SELECTION

DESCRIPTION

CAPACITY
CUT OFF

SAFETY
TIME

TEMP
CUT OFF

This program sets the maximum charge capacity that will be
supplied to the battery during charge. If the delta peak voltage
is not detected nor the safety timer expired by any reason, this
feature will automatically stop the process at the selected
capacity value.

When you start a charge process, the integral safety timer
automatically starts running at the same time. This is
programmed to prevent overcharge the battery if it proves to
be faulty, or if the termination circuit cannot detect the battery
full. The value for the safety timer should be generous enough
to allow a full charge of the battery.

The battery's internal chemical reaction will cause the
temperature of the battery to rise. If the temperature limit is
reached, the process will be terminated.

OFF
100-20000 mAh

OFF
1-720 Min

20 C/68 F -
80 C/176 F

SETTING

ABOUT

ABOUT

System information: model no., serial no., hardware version,
software version.

SETTING

Lilon

6S C2.0A/D1.0A

BATT TYPE

Pb

LiPo

Lilon

OPERATION

CHARGE

BAL CHARGE

VOLT METER

P2

CELLS

CAPACITY

START

SETTING PRESET

mAh

Advertising