Treasure Garden AMK Mount Kits - Manual (Page 4)

3
Base Plate
Machine
Bolts
AP/AKZ
Rotating Hub
AMK
Adapter Plate
Hub Bolts
& Washers
S T E P 1 Base Plate
Locate one base plate in the desired location on the deck. The base plate should overlap two
deck planks evenly. Adjust the base plate so that the proper alignment is ensured.
S T E P 2 Drilling Deck Planks
Mark the four holes onto the deck for drilling. Drill four 10mm holes through the deck planks for
the machine bolts. Remove enough deck screws or nails from these planks to be able to install
base plate underneath the planks.
S T E P 3 Attach Base and Adapter Plates to Deck Planks
Attach the base plate and adapter plate together, with the base plate under the deck and the
adapter plate (countersunk holes down) on top of the deck planks, using four (4) machine
bolts and nuts ( Contractor will determine size and provide machine bolts and nuts).
Insert the machine bolts downward through the top of the adapter plate, through the planks,
and screw them into the threaded holes in the bottom base plate. Make sure they are very
tight.
S T E P 4 Fasten Deck Planks
Refasten the deck planks to the joists by attaching removed screws from Step 2 in the original
holes closest to the base plate. Two structural deck screws should be used on either side of the
base plate in each plank.
S T E P 5 Attach Rotating Hub to Adapter Plate
Attach rotating hub to adapter plate using the hub bolts and washers that came with your
umbrella.
S T E P 6 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella Instruction Manual for
further assistance.
You are now ready to operate your umbrella!
REMOVAL:
To remove your umbrella for seasonal storage or to move it to another base plate or
in-ground fitting, see your umbella Instruction Manual for further assistance on how to remove
umbrella.
WOODEN DECK MOUNT KIT
Wooden Deck Mount Kit includes:
A -
Adapter Plate
B - Base Plate
B
A
4
IN-GROUND MOUNT KIT
S T E P 1 Preparation
The in-ground fitting should or can be built
into newly poured concrete. For a perfect
flush mount, set the plate of the fitting
3/8” below the final surface grade. When
you add the 3/8” thick adapter plate to the
fitting plate, the adapter plate will be flush
with the concrete.
S T E P 2 Bolt Adapter Plate
Once installed and the concrete has cured,
bolt the adapter plate (countersunk holes
face up) to the top of the in-ground fitting
using the four (4) stem bolts and allen
wrench. Insert the stem bolts downward
through the countersunk holes in the
adapter plate and screw them into the
threaded holes in the top of the in-ground
fitting. Make sure they are very tight.
S T E P 3 Attach Rotating Hub
Attach rotating hub to adapter plate using
the hub bolts and washers that came with your umbrella.
S T E P 4 Attach Umbrella
Slide frame over the newly mounted rotating hub. See your umbrella Instruction Manual for
further assistance.
You are now ready to operate your umbrella!
IMPORTANT: When concreting the in-ground fitting in place, make sure not to get slurry in
the screw threads. Either apply tape over the holes on both sides of the fitting or place the
stem bolts in the threads and withdraw them when the concrete is set. Make sure that the
in-ground fitting is perfectly level. Allow the concrete to cure for the appropriate cure time for
your area before installing the umbrella onto the fitting.
REMOVAL:
To remove your umbrella for seasonal storage or to move it to another base plate or
in-ground fitting, see your umbrella Instruction Manual for further assistance on how to remove
umbrella.
C
B
Ground Level
Concrete Footing
Flare at
bottom
1.0m
or
3’4”
In-Ground
Fitting
AMK
Adapter Plate
Ground
Stem Bolts
AP/AKZ
Rotating Hub Hub Bolts
& Washers
Hole Diameter
500mm or 21” - 24”
A
D
In-Ground Fitting Kit includes:
A -
Adapter Plate (8.5” diameter) C - Stem Bolts (4)
B - In-Ground Fitting D - Allen Wrench