WebDT SA3000P - Manual (Page 2)

SA3000P
ENGLISH 2 3 ENGLISH
THE SA3000P Signage Appliance
Rear View Front View
A B C D F E G H
Ethernet port
HDMI port
VGA port RS232 COM port
DC-in D
F
E
G
H
A
B
C
Audio jacks
Power button
USB 2.0 (2)
Precautions
Always exercise care when operating and handling. •
Never disassemble any portion of the enclosure. It will void any product warranty. •
Do not use any AC/DC adapter other than the one provided with the device or acquired from •
the manufacturer or its partners.
In the unlikely event that smoke, abnormal noise, or strange odor is present, immediately
•
power down the product and disconnect all power sources.
Please report the problem to your device provider immediately.
•
Pushing on the Power Button again will restart the appliance.
Powering ON and OFF
The SA3000P is programmed to Power On automatically when power is first applied or re-
established. There is also a Power Button, located on the front of the SA3000P. To turn the
SA3000P on, push and release the Power Button on the front bezel. The adjacent power LED will
be lit (blue), and the corresponding interface will be shown on the display monitor.
To turn off the device, use the software shutdown interface provided.
In the event of system lockup, unplug or re-plug the power cable. Also, the Power Button may
be used to perform a reset of the device. To do that, push and hold the Power Button for at least
4 seconds. The system will shut down and all unsaved work may be lost. Pushing on the Power
Button again will restart the device.
Server Installation
Please refer to the corresponding User Guides for software installation instructions.
Connect Player and Register to WCM Server
When you power on your signage player, the registration dialog will be launched automatically. •
You can also launch it from Start | All Programs | DT Research | WebDT Signage Player |
Register Player Again.
NOTE: If your signage player is located in a LAN with a WCM server, the player will
automatically register to the server in the same LAN.
Registration Information:
Player name: Leave default name or give a new name
Group name: If you did not create any group in WCM
server yet, leave it blank now
Organization name: my site (default)
Access Password: 123456 (default)
Publish Server URL:
http://(server IP address): (port number)/publish
or, http://localhost: (Port number)/publish
To exit the full screen introduction, press “Ctrl+Shift+Space” to exit the WebDT Signage Player. •
To re-launch the WebDT Signage Player, • navigate to Start | All Programs | DT Research |
WebDT Signage Player | Start player.
To register this signage appliance to
• another WebDT Content Manager Server, navigate to Start
| All Programs | DT Research | WebDT Signage Player | Register Player Again, and then the
Player Registration dialog will be launched. Fill in all fields to register. Click OK to register and
connect to the preferred WebDT Content Manager Publish Server.
Please refer to documentation included in the DVD of your package to start
• managing your
content, playlists and schedules via WebDT Content Manager.
Options
The SA3000P Signage Appliance is designed to work with a range of custom and off-the-shelf
options to enhance its applicability for various deployments.
* Internal PCI Express wireless LAN (WLAN) adapters with dipole antenna
VESA Mounting Bracket Installation Guide for SA3000P
The DT Research Signage Appliance package includes a VESA-compliant mounting bracket (1)
which mounts the SA3000P (2) onto a VESA-compatible monitor or display.
NOTE: The VESA Mounting Bracket is compatible with most displays and monitors that support
the VESA standard.
Step1:
Locate the existing mounting holes on the monitor. •
Line the bracket holes up with the holes on the back of the monitor, as shown to the right. •
Place the screws to hold the mounting bracket in place and tighten the screws (do not over- •
tighten).
Step2:
Remove the two M3 screws (3) originally on the SA3000P signage appliance. •
Place the SA3000P (2) on the bracket rail with the interface ports side facing downwards so •
that the two mounting holes on the appliance are aligned with the existing holes on the rail
(see picture).