Naim Audio SUPERNAIT 2 User Manual

Naim Audio Receivers and Amplifiers

Advertising

This manual is related to the following products:

NAIT XS 2 NAIT 5si

Table of contents

Document Outline

Contents
1 Connections
- 1.1 Interconnect Cables
- 1.2 Loudspeaker Cables
2 Mains Power
- 2.1 Mains Plug Wiring
- 2.2 Equipment Fuses
- 2.3 Non-rewirable Mains Plugs
- 2.4 Mains Circuits and Cables
3 General Installation
- 3.1 Siting The Equipment
- 3.2 Switching On
- 3.3 Running In
- 3.4 Radio Interference
- 3.5 Lightning Precautions
- 3.6 Problems?
- 3.7 Service and Updates
4 SUPERNAIT 2 Introduction, Installation and Connection
- 4.1 Mains Power Connection
- 4.2 Signal Inputs
- 4.3 Speaker Outputs
- 4.4 av and hdd Outputs
- 4.5 Headphone Output
- 4.6 AV Bypass
- 4.7 Other Signal Inputs and Outputs
- 4.8 Power Supply Upgrades
- 4.9 General Connections Notes
- 4.10 External Control and Interface
5 Controls and Connections
- 5.1 Front Panel Controls
- 5.2 Rear Panel Connections
6 System Connections
- 6.1 SuperNait 2 with Hi-Cap Power Supply
- 6.2 SuperNait 2 with additional NAP 200 Power Amplifier
- 6.3 SuperNait 2 with Hi-Cap Power Supply and NAP 200 Power Amplifier
7 Amplifier Operation and Programmable Functions
- 7.1 Automatic Input Switching
- 7.2 Handset Volume and Balance Control
- 7.3 Mute
- 7.4 Display
- 7.5 Switch-on
- 7.6 Remote Control
- 7.7 Defaults
- 7.8 Fault Conditions
8 Specifications
9 NAIT XS 2 Introduction, Installation and Connection
- 9.1 Mains Power Connection
- 9.2 Signal Inputs
- 9.3 Speaker Outputs
- 9.4 av and hdd Outputs
- 9.5 Headphone Output
- 9.6 AV Bypass
- 9.7 Other Signal Inputs and Outputs
- 9.8 Power Supply Upgrades
- 9.9 General Connections Notes
- 9.10 External Control and Interface
10 Controls and Connections
- 10.1 Front Panel Controls
- 10.2 Rear Panel Connections
11 System Connections
- 11.1 Nait XS 2 with FlatCap XS Power Supply
- 11.2 Nait XS 2 with Hi-Cap Power Supply and NAP 200 Power Amplifier
12 Amplifier Operation and Programmable Functions
- 12.1 Automatic Input Switching
- 12.2 Handset Volume Control
- 12.3 Mute
- 12.4 Display
- 12.5 Switch-on
- 12.6 Remote Control
- 12.7 Defaults
- 12.8 Fault Conditions
13 Specifications
14 NAIT 5si Introduction, Installation and Connection
- 14.1 Mains Power Connection
- 14.2 Signal Inputs
- 14.3 Speaker Outputs
- 14.4 hdd Output
- 14.5 Headphone Output
15 Controls and Connections
- 15.1 Front Panel Controls
- 15.2 Rear Panel Connections
16 Amplifier Operation and Programmable Functions
- 16.1 Automatic Input Switching
- 16.2 AV Bypass
- 16.3 Handset Volume Control
- 16.4 Mute
- 16.5 Display
- 16.6 Remote Control
- 16.7 Defaults
- 16.8 Fault Conditions
17 Specifications
18 NARCOM 4 Remote Handset
- 18.1 Using NARCOM 4
- 18.2 NARCOM 4 Keys
19 Declaration of Conformity
20 Statutory Safety Warnings