Dt-5, Dt-15, Product specifications – Pengo DT-5 User Manual
Page 10: Two speed models must have a minimum of 20gpm
10
Two Speed (DT & RT) Series Manual
PRODUCT SPECIFICATIONS
Output speed and torque specifi cations are NOT listed at 100% effi ciency. Maximum effi ciencies have been applied to the torque
and speed charts according to the manufacturers recommendations. Speed and torque output are dependent on the overall
system effi ciencies associated with the prime movers hydraulic system. When the purchaser is determining criteria for specifi c
applications please contact Pengo. Pengo has made every attempt to present accurate and suitable information published on this
document. This document should be used for information and comparative purposed only. When application specifi c information is
required, please contact Pengo.
Pengo continually looks for new ways to improve its products. Therefore, Pengo reserves the right to make changes to our
products and specifi cations without notice.
TOTAL UNIT WEIGHT
645 LBS / 292 Kg
HYDRAULIC MOTOR INFORMATION
Displacement
2.98 cu/in (97.6cc)
Motor Type
Two Speed Bi-Directional
Motor Output Shaft
1-1/4" Spline 14T
Motor Mount
SAE - C 4 Bolt
Motor Ports
1-5/8" - 12 UN-2B
Cross Over Pressure Relief
Set @ 3100 psi
PLANETARY GEARBOX INFORMATION
Gearbox Type
Planetary Two Stage
Reduction Ratio
25.36:1
Output Shaft
2-1/2" Hex
Oil Capacity
2.0 Gallons
Oil Type
SAE 80W90 GL-5
Shaft Pull Out (lbs.)
22,500 lbs.
REFERENCE TORQUE CHART
Pressure PSI (Bar)
High Torque (ft/lbs)
Low Torque (ft/lbs)
1600 (110)
2629
1314
1800 (124)
2958
1478
2000 (137)
3287
1643
2200 (151)
3615
1807
2400 (165)
3943
1971
2600 (179)
4272
2136
2800 (193)
4601
2300
3000 (206)
4930
2465
REFERENCE SPEED CHART
Flow GPM (Liter)
Low Spd (rpm)
High Spd (rpm)
20 (75)
25
50
25 (95)
31
63
30 (113)
38
75
35 (132)
44
88
40 (151)
50
100
AUGER DRIVE MODEL
dt-5
Two speed models must have a minimum of 20GPM.
TOTAL UNIT WEIGHT
825 LBS / 374 Kg
HYDRAULIC MOTOR INFORMATION
Displacement
17.8 cu/in (293cc)
Motor Type
Two Speed Bi-Directional
Motor Output Shaft
1-1/4" Spline 14T
Motor Mount
SAE - C 4 Bolt
Motor Ports
1-5/8" - 12 UN-2B
Cross Over Pressure Relief
Set @ 3100 psi
PLANETARY GEARBOX INFORMATION
Gearbox Type
Planetary Two Stage
Reduction Ratio
26.52:1
Output Shaft
3" Hex
Oil Capacity
3.0 Gallons
Oil Type
SAE 80W90 GL-5
Shaft Pull Out (lbs.)
22,500 lbs.
REFERENCE TORQUE CHART
Pressure PSI (Bar)
High Torque (ft/lbs)
Low Torque (ft/lbs)
1600 (110)
8254
4127
1800 (124)
9287
4643
2000 (137)
10318
5159
2200 (151)
11350
5674
2400 (165)
12382
6191
2600 (179)
13414
6707
2800 (193)
14445
7223
3000 (206)
15478
7738
REFERENCE SPEED CHART
Flow GPM (Liter)
Low Spd (rpm)
High Spd (rpm)
20 (75)
8
16
30 (113)
12
24
40 (151)
16
32
50 (190)
20
40
AUGER DRIVE MODEL
dt-15