Casio Operation Guide 3216 - Manual (Page 4)

Operation Guide 3216 3223
E-30
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal ( SIG ).
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
ll llll ll l lll
Hourly time signal
on indicator
E-31
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 59 minutes, 59.99
seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-9).
ll llllll ll ll
1/100 second
Seconds
Minutes
E-32
To measure times with the stopwatch
Elapsed Time
Split Time
Two Finishes
D
Start
D
Start
D
Start
Stop Re-start Stop
D D D
Split
(SPL displayed) Split release Stop
A D A
Split
First runner finishes.
Display time of first
runner. Stop
Second runner
finishes. Split release
Display time of
second runner.
D A A
A
A
A
➤ ➤ ➤
➤ ➤ ➤
➤ ➤ ➤
➤
➤
➤
Clear
Clear
Clear
E-33
Countdown Timer
Dual timers can be set with two different starting times.
The watch can be configured so the two timers alternate,
so when one reaches the end of its countdown, the other
timer starts. You can specify a “number of repeats” value,
which controls how many times the two-timer countdown
operation is performed (1 = once, 2 = twice, etc.). The
starting time of each timer can be set in five-second steps
up to 99 minutes, 55 seconds.
You can specify up to 10 repeats. The watch emits a short
beep whenever either of the timers reaches the end of its
countdown during an ongoing timer operation. The watch
emits a 5-second beep when the end of the final timer
operation (specified by the number of repeats) is reached.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero. The
beeper stops after about 5 seconds or when you press any button.
ll llllll ll ll
Seconds
Timer 1
Minutes
Number of Repeats
E-34
To configure the countdown timer
1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-36) to display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
l l l ll
ll
lll
lll
ll
ll
ll llllll ll ll
E-35
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Button Operation
Use D (+) and B (–) to change the setting.
Use D (+) and B (–) to change the setting.
Setting
Minutes, Seconds
Number of Repeats
Screen
• To disable either timer, set 00'00" as its countdown start time.
4. Press A to exit the setting screen.
E-36
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• The countdown is performed by alternating between Timer 1 and Timer 2. A short
beep is emitted to signal a changeover from one timer to the other.
• Pressing A while a countdown timer is stopped resets it to the start time specified by you.
• Press D to pause a countdown. Press D again to resume.
• The watch emits a 5-second beep when the end of the final timer operation
(specified by the number of repeats) is reached.
• Even if you exit the Countdown Timer Mode, the countdown timer operation
continues and the watch beeps as required.
• To stop a countdown operation completely, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
ll llllll ll ll
Current timer time
Timer 1 or 2
Current repeat count Present number of repeats
(Reset)
(Start/Stop)
Current time
E-37
Illumination
This watch has an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark. The watch’s auto light switch turns on illumination
automatically when you angle the watch towards your
face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• See “Illumination Precautions” (page E-63) for other
important information about using illumination.
To illuminate the display manually
In any mode (except when a setting screen is on the
display), press
B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
ll
lll ll
ll lll
ll ll
lll ll
ll lll
ll
Auto light switch on
indicator
E-38
• You can use the procedure below to select either 1.5 seconds or 3 seconds as the
illumination duration. When you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current illumination duration setting.
To specify the illumination duration
1. In the Timekeeping Mode, hold down A until the
display contents start to flash. This is the setting screen.
2. Press C 10 times until the current illumination duration
setting ( or ) appears.
3. Press D to toggle the setting between
(approximately 1.5 seconds) and (approximately
3 seconds).
4. Press A to exit the setting screen.
ll lllll
llll ll l
E-39
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on, whenever you position
your wrist as described below in any mode. Note that this watch features a “Full Auto
EL Light”, so the auto light switch operates only when available light is below a certain
level. It does not turn on the backlight under bright light.
Moving the watch to a position that is parallel to the ground and then tilting it towards
you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Parallel to
ground
More than 40°