Bebe Confort Priori XP - Manual (Page 6)

Instructions for use
• Now return the handle to its original position (click) making sure it rests against the base (12). The belt tensioner
tightens the seat belt even further. The belt tensioner should now be positioned between both belt hooks on the lap
belt (13).
• You can now adjust the shell of the Bébé Confort Priori XP into the desired position.
Placing your child in the Bébé Confort Priori XP
• Loosen the shoulder belts by pressing the release button and pulling the shoulder belts towards you (14). Important:
Do not pull on the belt pads when doing so.
• Open the belt buckle (15) and drape the belts over the hooks on the shell (16).
• Pull the buckle forwards and hook the belt pad over lip (17).
• Position your child comfortably with his/her back against the shell (18) and make sure that there are no toys or other
hard objects in the shell.
• Slide buckle tongue sections together and insert them into the buckle (19).
• Position the lap belt as low as possible to ensure the hips sit firmly in the seat.
• Pull the shoulder belts tight (20/1) and pull the remaining slack out of the belt system by pulling the belts tight using
the adjuster belt (20/2).
IMPORTANT!
• The tighter the belts fit around your child, the better the protection. You should be able to fit only one finger between
the belts and your child.
• The textured side of the belt pads must be placed on your child’s shoulders.
• The belts should never be twisted.
• If you are unable to click the buckle sections into the buckle, unblock the buckle by pressing the red button and try
again.
• If you are not able to fasten the seat belt system properly or pull it tight, contact your supplier immediately. Do not
use the Bébé Confort Priori XP under any circumstances!
Adjusting the height of the shoulder belts
The correct belt height of the shoulder belts is attained when the belt disappears into the shell slightly above the
shoulder of the child. Make sure that the shoulder belts fit properly over the shoulders of the child (21).
• Loosen the shoulder belts by pressing the release button and pulling the shoulder belts towards you as far as
possible (14) Important: Do not pull the belt pads when doing so.
• Lift up the flap on the cover by the shoulder belt slots (22).
• To make the adjustment easier, pull the shoulder belts on top of the belt pad forward into a loop, loosening them (23).
• Next, push the loop back through the opening (24).
• Slide the shoulder belt and the belt pad strap through the slot together into the next position (25). Make sure that the
shoulder belt is positioned on top of the belt pad strap in the new position (26). Always do this on both sides.
• Pull the shoulder belts tight by pulling on the belts under the belt pads (26).
• Place the flap back in position and thread the belt pads through the correct slots in the flap and secure them with the
Velcro (27).
• Check whether you are able to use the belts and ensure they are not twisted.
Maintenance, removing the cover and belt pads
Remove the Bébé Confort Priori XP from the car before carrying out any of the following.
• The seat may be cleaned with lukewarm water and a gentle soap. Do not use abrasive detergents.
• The cover and the belt pads must be washed by hand at a maximum temperature of 30
o
C. Do not use a dryer. Also
see washing instructions.
• The belt buckle may be cleaned with warm water. Do not lubricate.
• It is advisable to buy an extra cover when you purchase the Bébé Confort Priori XP, so that you can use the Bébé
Confort Priori XP at all times, such as when the cover has to be cleaned (or dried).
GB
10
0528004 PRIORI BBC LIVRET.qxd:gba-priori-1-xp-624-bw 29/06/09 16:49 Page 10