CHIAYO ITALK - Manual (Page 2)

1. Mic in socket for headset/lavalier/wired microphone
2. Power/bettery low indicator LED
3. Power/volume control
4. Tone control
5. Charging indicator LED
6. Charging port
1. Mic in socket for headset/lavalier/wired microphone
2. Power/bettery low indicator LED
3. Power/volume control
4. Tone control
5. Charging indicator LED
6. Charging port
Standard Configuration
1. Beltpack amplifier
2. 6V DC/500mA charging adaptor
3. Φ3.5mm signal cable(100cm)
4. Waist Belt
5. Speaker pouch
6. Operation manual
Standard Configuration
1. Beltpack amplifier
2. 6V DC/500mA charging adaptor
3. Φ3.5mm signal cable(100cm)
4. Waist Belt
5. Speaker pouch
6. Operation manual
Personal Beltpack Amplifier
Personal Beltpack Amplifier
4
4
6
6
5
5
Optional Items
1. NiMH battery (1.2V / 2600 mAH)
2. Headset microphone
3. Lavalier microphone
4. Mini wired microphone (3.5mm phone jack + 120cm cable)
Optional Items
1. NiMH battery (1.2V / 2600 mAH)
2. Headset microphone
3. Lavalier microphone
4. Mini wired microphone (3.5mm phone jack + 120cm cable)
Parts and Controls
Parts and Controls
1
1
2
2
3
3
Input microphone selections
1. Headset microphone
Operating Instructions
1. Please beware of battery polarity when installing the rechargeable batteries.
The spring end being the negative contact. For first use, please charge the
batteries for at least 6 hours. Thereafter 6 to 8 hours of charging is
necessary when batteries become weak.
2. This unit is delivered with adjustable waist belt. It can be belt-packed or
shoulder-strapped.
3. Turn Volume and Tone controls to minimum before switch on. After turning
this unit on, adjust volume and tone controls gradually till maximum gain
before feedback.
4. Insert the microphone plug completely into the MIC IN socket to get the full
contact, otherwise contact noise may occur due to loose contact. Adjust the
microphone to as near the mouth as possible to get the best voice pickup.
5. Microphone and speaker should always maintain a certain distance to
prevent the unpleasant feedback effect.
Battery installation
iTalk uses 4 AA-sized batteries to operate. To install the batteries, please
open the cover of its rear battery compartment, then place them in
accordance with its indicated polarity.
Input microphone selections
1. Headset microphone
Operating Instructions
1. Please beware of battery polarity when installing the rechargeable batteries.
The spring end being the negative contact. For first use, please charge the
batteries for at least 6 hours. Thereafter 6 to 8 hours of charging is
necessary when batteries become weak.
2. This unit is delivered with adjustable waist belt. It can be belt-packed or
shoulder-strapped.
3. Turn Volume and Tone controls to minimum before switch on. After turning
this unit on, adjust volume and tone controls gradually till maximum gain
before feedback.
4. Insert the microphone plug completely into the MIC IN socket to get the full
contact, otherwise contact noise may occur due to loose contact. Adjust the
microphone to as near the mouth as possible to get the best voice pickup.
5. Microphone and speaker should always maintain a certain distance to
prevent the unpleasant feedback effect.
Battery installation
iTalk uses 4 AA-sized batteries to operate. To install the batteries, please
open the cover of its rear battery compartment, then place them in
accordance with its indicated polarity.
Personal Beltpack Amplifier
Personal Beltpack Amplifier
2. lavalier microphone 3. Mini wired microphone
2. lavalier microphone 3. Mini wired microphone