Denon DN-HS5500 - Manual (Page 13)

8
ENGLISH
ENGLISH
q Loop mode indicat ors
• DN-HS5500 has Loop mode indicators which
consist of A , B and two arrows. A and B marks
indicate A and B points have been set.
• Two arrows indicate loop setting mode as follows.
or Left arrow only on:
Hot Start mode
Both arrows on:
Seamless Loop mode
, Both arrows flashing:
Seamless Loop Playing
, Left arrow on, right flashing:
Exit play from Seamless Loop
w Pitch display
• This indicator display the playback speed (pitch).
e Navigation display
• With the DN-HS5500, such operations as selecting
the mode, etc., can be performed using the
PARAMETERS knob following the instructions on
the navigation display. The PARAMETER indicator
flashes when it is possible to input using the
PARAMETERS knob.
r KEY ADJ. indicator
• KEY ADJ. indicator appears in display when the Key
Adjust mode is ON.
t MEMO indicator
• MEMO indicator appears in display when there is a
memo setting found for the current playing
File/Playlist or the File/Playlist at which the Cue
standby mode is currently set.
y BPM indicators
• Lights when the BPM is displayed on the pitch
display.
u Character display
• You can select the mode or function using
PARAMETERS knob following the short message
which is displayed on the character display area.
• The character display indicates the operation,
mode name, data, etc., and displays such guide
messages as “Push/Play” means if “YES”, push
PARAMETERS knob. The display indicates
and
marks sometime, note that mark says you
to turn PARAMETERS knob and marks says to
push PARAMETERS knob.
• The PARAMETER indicator flashes when you can
use PARAMETERS knob, otherwise this knob used
for File Selection.
i BPM point display
• Displayed when the BPM value of the “A1” or
“A2” point is being calculated.
(3) Display
o Visual Marker
• This turns according to the playing status of the
different decks.
Use this as an indicator for scratching and other
JOG operations.
!0 Play Position indicators
• Play position indicator:
The 20 dots indicator a visual position marker
during normal play. In the reverse play mode, the
dots are inverted.
• End of Message:
When the file’s end time is below the specified
time, the lower section of the play position
indicators flashes according to the file’s remaining
time (EOM), indicating the end of the file.
✽The EOM time can be set in the presets.
!1 Minute, second and frame displays
• These displays indicate current position
information.
!2 Time mode indicators
• When the TIME button is pushed, the Time mode
indicator switches as follows:
ELAPSED:
File’s elapsed time is displayed.
REMAIN:
File’s remaining time is displayed.
T. ELAPSED:
The total elapsed time of Playlist is displayed.
T. REMAIN:
The total remaining time of Playlist is displayed.
!3 Device display
• This displays the device currently selected for the
different decks.
!4 Keyboard connection indicator
• Deck for which keyboard is effective is now
displayed.
Keyboard input effective for Deck 1
Keyboard input effective for Deck 2
Keyboard input not dependent on deck (Utility
Mode, etc.)
!5 Mode display
• Upper section: Displays the current mode of the
different decks.
• Lower section: Displays the current playlist name,
artist name, etc., for the different decks.
!6 Play mode indicators
• When SINGLE indicator lights up, playback will
finish at end of current file.
• When CONT. indicator lights up, playback
continues.
!7 Database Creation indicator
• This lights when a database is being created.
!8 External device connection
confirmation indicator
• This flashes when an external device
is connected. When flashing, press the SOURCE
button to select the device. (The indicator does not
flash when a keyboard is connected.)
!9 HDD indicator
• This lights when the HDD is being accessed.
@0 Track indicator
• When in the playlist playback mode for the different
decks, the track at which the play, pause or cue
mode is set is displayed here.
Nothing is displayed when in the file playback
mode.
@1 File data indicator
• This indicates the currently selected file format
(“WAV” or “MP3”) for the different decks. When
the currently selected file format is “MP3”, the bit
rate, etc., is also displayed.
@2 USB indicator
• This lights when a USB hard disc or USB thumb
drive is being accessed.
✽Do not disconnect the USB device while the
indicator is lit.
@3 2STEP indicator
• Displayed when the number of search steps for the
file search mode is set to 2.
@4 Cross Fader indicator
• This lights during crossfader playback.
Dual display mode
@2 @3
@4 e i o
!7 !8 !6 !2 !9 !4 !5 @00 @1 !6 !3!2!1!0
q w t r y u