Digi ACCELEPORT EPC/CON-16 - Manual

91000749 A
Step Five: Install peripheral cabling
You can connect printers, terminals, modems (or any other standard EIA-
232 device to be controlled by applications on the computer) to the
EPC/CON-16 concentrator by installing a cable between the peripheral
and the concentrator.
On the peripheral end of the cable, the cable connector depends on the
requirements of the peripheral. The EPC/CON-16 (or PORTS/Xem mod-
ule) end of the cable must fit either an RJ-45 or DB-25 connector,
depending on the model you have.
The pin assignments for each type of EPC/CON-16 connector are as fol-
lows:
DB-25 Pin assignments
RJ-45 pin assignments are shown on the back.
RJ-45 Pin Assignments
Refer to the CD-ROM for more detailed cabling information.
What Next?
At this point the hardware installation for your EPC/X system is com-
plete. However, since the EPC/X adapter and the EPC/CON-16 concen-
trators must have software downloaded to their internal RAM before they
become functional, you must next install the software drivers for your
operating system.
•
Read the instruction booklet for the CD-ROM that came with your
system for instructions on installing software.
• View the on-line documentation on the CD-ROM for more informa-
tion about your EPC/X system.
The Digi logo and AccelePort are registered trademarks of Digi International. EPC/X,
EPC/CON-16, PORTS/Xem PORTS/8em, PORTS/16em, Modem/Xem, Modem/4em, and
Modem/8em are trademarks of Digi International.
All other brand and product names are trademarks of their respective holders.
© Digi International Inc., 1998; All Rights Reserved; http://www.dgii.com
Information in this document is subject to change without notice and does not represent a
commitment on the part of Digi International.
Digi provides this document “as is”, without warranty of any kind, either expressed or
implied, including, but not limited to, the implied warranties of fitness or merchantability
for a particular purpose. Digi may make improvements and/or changes in this manual or in
the product(s) and/or the program(s) described in this manual at any time.
This product could include technical inaccuracies or typographical errors. Changes are peri-
odically made to the information herein; these changes may be incorporated in new editions
of the publication.
AccelePort EPC/X System
EPC/X PCI Host Adapter
EPC/CON-16 Concentrator
Hardware
Installation Guide
Introduction
An AccelePort
®
EPC/X
™
system consists of an EPC/X host adapter cou-
pled with EPC/CON-16
™
concentrators from which EIA-232 peripheral
devices such as printers, terminals or modems can be cabled and con-
trolled. The adapter has two lines that can each support one or more con-
centrators. Multiple concentrators can be linked in a chain, and Digi
PORTS/8em
™
, PORTS/16em
™
, Modem/4em
™
, and/or Modem/8em
™
modules can be added to a concentrator to expand the number of ports
available.
Figure 44. Example EPC/X setup
This installation guide describes how to plan your setup and install the
EPC/X host adapter and concentrator hardware.
Signal Description Pin
GND Chassis Ground 1*
TxD Transmitted Data 2
RxD Received Data 3
RTS Request To Send 4
CTS Clear To Send 5
DSR Data Set Ready 6
SG Signal Ground 7
DCD Data Carrier Detect 8
DTR Data Terminal Ready 20
RI Ring Indicator 22
* Chassis Ground is also available on the
connector shell
Signal Description Pin
RI Ring Indicator 1
DSR Data Set Ready 2†
RTS Request To Send 3
GND Chassis Ground 4
TxD Transmitted Data 5
RxD Received Data 6
SG Signal Ground 7
CTS Clear To Send 8
DTR Data Terminal Ready 9
DCD Data Carrier Detect 10
† Pin 2 can be configured for DCD (through Digi
software) if you want to connect using an 8 pin
connector