Marantz PM7004N - Manual (Page 18)

12
ENGLISH
• Power output
(20 Hz – 20 kHz simultaneous drive of both channels): 70 W x 2 (8 Ω load)
100 W x 2 (4 Ω load)
• Total harmonic distortion
(20Hz – 20kHz simultaneous drive of both channels, 8Ω load): 0.02%
• Output band width
(8Ω load, 0.05%): 5Hz – 60kHz
• Frequency response
(CD, 1W, 8Ω load): 5Hz – 100kHz ±3dB
• Dumping factor
(8Ω load, 20Hz – 20kHz): 100
• Input sensitivity/Input impedance
PHONO (MM): 2mV/47kΩ
CD, TUNER, AUX/DVD, RECORDER: 200mV/20kΩ
MAIN IN 1.6V/15kΩ
• Output voltage/Output impedance
PRE OUT 1.6V/600Ω
• Maximum allowable PHONO input level (1kHz)
MM 100mV
• RIAA deviation (20Hz ~ 20kHz) ±0.5dB
• S/N (IHF-A, 8Ω load)
PHONO (MM)
(PM-KI-PEARL-LITE) 87dB (5mV input, 1W output)
(PM7004) 85dB (5mV input, 1W output)
CD, TUNER, AUX/DVD, RECORDER
(PM-KI-PEARL-LITE) 106dB (2V input, Rated output)
(PM7004) 104dB (2V input, Rated output)
POWER AMP DIRECT IN . 125dB (Rated output)
• Tone control
Bass (50Hz) ±10dB
Mid (900Hz) ±6dB
Treble (15kHz) ±10dB
• Power requirement AC 230V 50/60Hz
• Power consumption
(EN60065) 200W
Standby power consumption 0.3W
• Weight
PM-KI-PEARL-LITE 11.2kg
PM7004 10.5kg
For the purpose of improvement, the specifi cations and design are subject to change without notice.
Specifications Index
v A
Adjusting the tone ················································ 9
Adjusting the volume ··········································· 9
Auto standby mode ············································ 10
v B
BALANCE ························································· 4, 8
BASS ································································ 4, 8
Batteries ······························································· 3
Before use ···························································· 8
v C
Connection
Connecting cables ············································· 6
Connecting players ············································ 7
Connecting recorders ········································ 7
Connecting the speakers ······························· 6, 7
v I
INPUT SELECTOR ············································ 4, 8
v M
MID ·································································· 4, 8
Mute ································································· 4, 8
v P
POWER AMP DIRECT ····································· 4, 9
Power cord ··························································· 8
PRE OUT ························································ 4, 10
Protection circuit ············································ 6, 12
v R
Remote control ·········································· 3, 5, 10
v S
SOURCE DIRECT ············································· 4, 8
Speaker cables ················································· 6, 7
Stereo pin-plug cable ············································ 6
v T
TREBLE ···························································· 4, 8
v V
VOLUME ·························································· 4, 8
P
Protection Circuit
This is a function to prevent damage to components
within the power supply when an abnormality such
as an overload or excess voltage occurs for any
reason.
In this unit, the STANDBY indicator blinks and the
unit enters standby mode when an abnormality
occurs.
S
Speaker impedance
This is certain-rated resistance of the speaker set
to an alternating current and expressed in ohms.
The smaller the impedance, the greater the output.
However, load on the amplifier is increased. Use
speakers whose impedance is supported by this
unit.
Explanation terms
1.PM-KI PEARL LITE_N_ENG_0617.indd 12 2010/06/21 19:18:33