Marantz PM4400 - Manual (Page 8)

7
English
English
REMOTE CONTROL UNIT RC4200PM
The RC4200PM can be used to control a Marantz AV component
equipped with a remote sensor as well as other Marantz compo-
nents connected to the first component through the Remote
Control Bus. The buttons of the RC4200PM are laid out on its
control panel according to the functional groups as described
below.
z
POWER ON/OFF buttons
a. MAIN POWER ON button
Turns the PM4400's power on when it is in the stand-by
mode.
b. MAIN POWER OFF button
Sets the PM4400's power to the stand-by mode when it is set
to the power-on mode.
c. SOURCE POWER button
Switching the mode of a CD player, tuner, CD-R or other
Marantz component equipped with a power stand-by function
between power-on and stand-by is enabled by pressing this
button after the FUNCTION SELECT button corresponding
to the component has been pressed.
When this button is pressed after pressing the TUNER
button, the tuner's power is turned on; when it is pressed
again, the tuner is set to the stand-by mode.
When this button is pressed after pressing the AMP button,
the PM4400 is switched from the power-on mode to the
stand-by mode or vice versa.
x
FUNCTION SELECT button
PHONO button : When this button is pushed the input of
PHONO is selected.
CD button : When this button is pushed the input of
CD is selected.
TUNER button : When this button is pushed the input of
TUNER is selected.
CD-R button : When this button is pushed the input of
CD-R is selected.
AUX button : When this button is pushed the input of
AUX/DVD is selected.
DVD button : When this button is pushed the input of
AUX/DVD is selected.
TAPE button : When this button is pushed the input of
MD/TAPE is selected.
MD button : When this button is pushed the input of
MD/TAPE is selected.
c
VOLUME UP/DOWN button
UP button : VOLUME knob turns when this button is
pushed and the volume level is grows.
DOWN button : VOLUME knob turns when this button is
pushed and the volume level is falls.
v
MUTE button
When this button is pushed, the sound is not temporarily
emitted from the speakers.
When this button is pushed again, MUTE is released.
Moreover, when up/down of the volume is operated by
remote control, MUTE is released.
Other buttons are not applied to PM4400.
Please see at the owners manual of other equipment’s about
the operation of button.
2. Loading batteries
Batteries in this remote control unit have a life of approximately
1 year under normal operating conditions. When the remote
control unit is not to be used for an extended period of time,
remove the batteries. Also, when you notice that the batteries are
starting to run down, replace them as soon as possible.
(1)Remove the battery cover.
(2)Insert batteries with correct + / – orientation.
(3)Close the battery cover until it clicks shut.
USING THE REMOTE CONTROL UNIT
1. Remote control
Operate the remote control unit within a distance of approx. 5 m
from the infrared signal reception window (remote sensor) on the
front of the Amplifier.
Remote control operation may not be possible if the remote
control unit's transmitter is not pointing in the direction of the
remote sensor or if there is an obstruction between the
transmitteote sensor.
Remote control operating range
Remote control unit
Rear side
Two AA (R6)-size
batteries
Approx. 5 m
Amplifier
Remote control unit
60°
ON OFF
MAIN POWER SOURCE
POWER AMP
PHONO CD TUNER CD-R
AUX DVD TAPE MD
1 2 3  F/P
4 5 6 õ -/--
7 8 9 MODE
– 0 + MEMO
SCROLL CANCEL TEXT
OPEN/
CLOSE
TIME
z–MODE–x
MUTE
VOLUME
RC4200PM
SYSTEM REMOTE CONTROLLER
x
c
z
v