Daewoo DSC-3210EGB - Manual (Page 7)

SWITCHING ON TV SET
SWITCHING OFF
TV SET
DAILY USE
1) If stand-by indicator (B5) is red, then the TV set is in
stand-by mode.
You can switch on using the remote control POWER
button (A1), the NUMBER 0….9 buttons (A3), or
PROGRAM UP (A6) / DOWN (A21) buttons. The front
panel PROGRAM UP/DOWN buttons (B 2 ) can also be
used.
Once on, the stand-by indicator turns to green and the
picture appears on the screen.
2) If stand-by indicator (B5) is not lit, then the TV set
is powered off.
You must press the TV set front panel MAIN
POWER button (B1). If a picture does not appear,
then the stand-by indicator will be red. In this
case, use the remote control as indicated in 1).
3) If stand-by indicator (B5) is flashing red, and green
then the TV set is in child-lock mode.
It is necessary to use the remote control POWER button
(A1), NUMBER 0….9 buttons (A3), or PROGRAM UP
(A6) / DOWN (A21) buttons. The front panel PROGRAM
UP/DOWN buttons (B 2 ) will not function.
Once on, the stand-by indicator turns to green and the
picture appears on the screen.
1) By p ressing the remote control
POWER button (A1) ,you can
switch off to stand-by mode (low
power consumption mode) which
also allows quick restart by remote
control (see above: SWITCHING
ON TV SET).
2) Pressing the TV set front panel
MAIN POWER button (B1), you
can completely power off the TV
set. In this case, you must use the
same front panel POWER button
(B1) to switch on again (see
above: SWITCHING ON TV SET).
Remark: If a broadcast signal is not present after 30 minutes, the TV set will be automatically turned to stand-by mode.
PR
PR
MENU
SOUND CONTROL
Volume adjustment
Use the remote control VOLUME UP
(A20) / DOWN (A7) buttons or the TV set
front panel VOLUME UP / DOWN
buttons (B
3
).
Mono forcing, dual language
- If you are unable to get good sound
quality for a program due to poor
reception, you can force a change from
stereo to mono transmission by pressing
the remote control MODE button (A14).
Then the program status display
indicates "MONO" (in red).
- On the other hand, during a program
with dual language transmission, the
MODE button (A14) allows you to toggle
between the first and second language.
The program status display will indicate
"DUAL 1" or "DUAL 2" (plus NICAM
according to the received signal).
- To return to initial state, press again the
MODE button (A14).
Sound effects
A SPATIAL sound effect is available,
using the remote control 3D (A13) button.
The following display appears:
To return to initial sound effect, press
again the 3D (A13) button.
The following display appears:
As an option, the sound effects PANORAMA, and
VIRTUAL DOLBY are available with the same button.
For other adjustments (balance, equalizer, bass, treble), use the
Sound menu (page8).
Mute
Mute the sound by pressing the remote
control SOUND MUTE button (A2).
Then, logo is displayed. The previous
sound setting is returned after pressing
the same button a second time.
MENU
SPATIAL
STEREO
11:11
Spatial sound effect
Sound transmission mode
Clock
OFF
STEREO
11:11
No sound effect
Sound transmission mode
Clock
PROGRAM SELECTION (FROM 0 TO 99)
Direct selection
Use the remote control NUMBER 0….9
buttons (A3).
For two digits program numbers, enter
the second digit within 2 seconds.
Up / Down selection
Use the remote control PROGRAM UP
(A6) / DOWN (A21) buttons or the TV set
front panel
PROGRAM UP / DOWN buttons (B 2 ).
6