SONOSAX SX-S User Manual
Page 8
371.6.16 SX022270 SX-S Extension module
372. This module contains the SX022241 Stereo Analog Level & Phase Meter, plus the monitoring and communication functions, (including MS decoding). It is shipped with
the necessary Neutrik 6-pin chassis connector (SX860180) for connection to the SX-S Boom Box (SX022260) and the 12-pin chassis connector (SX860208) for
connection to the SX-S Extension Box. (SX022251). It also includes the necessary mounting hardware and connectors for installation in an existing SX-S mixer.
373.
374.6.17 SX022251 SX-S Extension box
375. The Extension Box is a signal distribution box (300mm x 56mm x 40mm) shipped with 1,5m of cable with the necessary connectors. Various connectors are installed in
the distribution box to interface the SX-S mixer with the Extension Module directly with the Stelladat, Nagra 4.2, and Nagra IVS, or other equipment.
376.
377.6.18 SX022260 SX-S Boom box
378. This small box connects to the SX-S Extension Module with an optional cable (SX922120). The box incorporates a 1/4" headphone socket, a 3 pin XLR socket for a
talkback microphone and a switch to call the mixer's operator with a "Roll" indicator.
379.
380.6.19 SX922120 SX-S Boom box cable
381. 2-pair shielded cable 10 meters in length (longer on request) with 6 pin XLR connectors on each end to connect the Boom Box with the SX-S Extension Module.
382.
383. RETURN TO TABLE OF CONTENTS
384.
385.
386.
7. INSTALLATION INSTRUCTIONS
for SX022270 SX-S Extension Module
387.
388.7.1 Equipment:
•
022270 SX-S Extension Module
•
SX922130 Internal cable extension module - Extension Box
•
SX922140 Internal cable extension module - Boom Box
•
SX860141 Socket 1/4'' with 150mm shielded cable and Dubox case
•
SX8600342 6 Pin socket connector
•
SX860500 6 Pin socket connector with 300mm flat cable
•
SX942291 Blank Panel Jack 4.4 (2x)
•
SX980124 Allen head screw M2,5x8 (4x)
•
SX980123 Allen head screw M2,5x6 (4x)
•
SX986420 Washer ribbed M2,5 (8x)
•
SX981134 Conical head screw M3x8 (4x)
•
SX642403 24 kOhms 1% R0805 Resistor (2x)
•
SXS351220 22pF 1% C0805 (1x)
•
SXS644990 49,9 Ohms 1% R0805 Resistor (1x)
•
SXS641503 15 kOhms 1% R0805 Resistor (1x)
•
SX860131 Bantam mini-jack pre-wired (1x)
•
SX140002 NPN-Transistor BC 550 C
389. When installing an SX022270 SX-S Extension Module in an SX-S mixing console with serial-number 16585 or lower R-64 and R-65 on the extension module operator
board need to be replaced by 24kOhms 1% SMD R0805.
390.
391.7.2 Procedure
392. On the Master Board (solder side) solder the 6 conductors of the ribbon cable(see PCB Layout)
393. Change Q1 (BC337) on the Masterboard with BC 550C (SX140002).
394. Mount the 12-pin Hirose socket in place of the last Input's 3-pin Neutrik.
395. Install the 6-pin Neutrik socket next to the 12-pin Hirose socket.
396. Install the Extension module beside the master board and connect the wires asindicated on the PCB Layout. Do not forget to install the additional 26-pin connector on
the SX-S10 ribbon cable.
397. SX-S 10
: Disconnect the Aux. XLR 3-pin male and replace it with SX860141,socket 1/4'' with 150mm shielded cable and Dubox case.
398. SX-S 6 SX-S 8
: Remove the existing 1/4'' Jack, unsolder the connections on the Masterboard and reconnect to the Bantam Jack with cable provided. Install the
SX860141, socket 1/4'' with 150mm shielded cable and Dubox case.
399. Click here for Illustration of INTERNAL connections, ajustments and switches
400. Click here for Master Module PCB Layout
401. NOTE:The ribbon cable connects to the PCB (from Left to right) Yellow - Brown - Orange - Green - Red - Blue.
402. Connections of the 6 pole Flatcable
403. Brown Cable
404. 1
405. PFL-BUS-left
406. Connected to pin No 1 OP-7
407. Red Cable
408. 2
409. MASTER-BUS-right
410. Connected to pin No 1 OP-3
411. Orange Cable
412. 3
413. PFL-BUS-right
414. Connected to pin No 7 OP-7
415. Yellow Cable
416. 4
417. Auxiliary BUS
418. Connected to cursor Aux
potentiometer
419. Green Cable
420. 5
421. PFL Control-CDE (sense)
422. Connected to point R-6/R-5/collector
of Q1
423. Blue Cable
424. 6
425. MASTER-BUS-left
426. Connected to pin No 7 OP-3